Cheap but dependabl...
 
Notifications
Clear all

Cheap but dependable

37 Posts
14 Users
0 Reactions
10.8 K Views
DrNeutron
Posts: 2018
(@drneutron)
Noble Member
Joined: 14 years ago

Do you own a DIYledexpress bridge?
If so the pixel extender is a great choice, can run up to 7.5Amp off the extender at 12 or 5V. I use mine with an old laptop power supply and run some 12V pixels.


Reply
Posts: 98
Topic starter
(@ronaldpa2)
Estimable Member
Joined: 12 years ago
DrNeutron wrote:Do you own a DIYledexpress bridge?
If so the pixel extender is a great choice, can run up to 7.5Amp off the extender at 12 or 5V. I use mine with an old laptop power supply and run some 12V pixels.

I do not.

Current setup is Pixlite 4 with FPP.


Reply
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago

The PI can control a certain number of pixels directly from its ports without a controller. Maybe that would be the best bet?


Reply
Posts: 1344
(@mrsmoofy)
Noble Member
Joined: 12 years ago

What about this http://www.holidaycoro.com/DMX-to-SPI-Smart-Pixel-Decoder-Controller-p/614.htm plus a power supply for it.


Reply
Posts: 1120
(@4586shaggy)
Noble Member
Joined: 14 years ago
MrSmoofy wrote:What about this http://www.holidaycoro.com/DMX-to-SPI-Smart-Pixel-Decoder-Controller-p/614.htm plus a power supply for it.

Issue with that one is that you cannot set your own sequencing. You have to use the pre-programmed effects.


Reply
Posts: 1344
(@mrsmoofy)
Noble Member
Joined: 12 years ago
4586shaggy wrote:Issue with that one is that you cannot set your own sequencing. You have to use the pre-programmed effects.

Yes you can. Look at the information about it

Sequencing software (when not used in standalone mode with built in sequences.) Applications include but are not limited to:
LOR S3
LightShow Pro
Vixen
As this controller is a standards based DMX unit (E1.11), any application that generates DMX is compatible.

And the Pixlite 4 has a DMX out on it so I would think he could use it in stand alone in the off season and then plug it into his pixlite 4 to use as part of his show.

You still need to waterproof it and have a power source.


Reply
Posts: 1120
(@4586shaggy)
Noble Member
Joined: 14 years ago

My bad. Was looking on my phone. Text was funny


Reply
AuburnLights
Posts: 213
(@auburnlights)
Estimable Member
Joined: 12 years ago

Have you looked at this? As long as you're only talking about E1.31 data (I'm not familiar with RobG's floods), it supports WS2811 and GECE (not that you care about that) and can support a minimum of one universe (possibly up to 4). Enclosure for the controller is just a 1" PVC pipe with ends. It would still require a Power supply of some type for the controller (although you could in theory run it off batteries) and the floods. It already has built-in wifi from the ESP8266-01 board so no control cables required. Group Buy was $10 + $3 for the ESP8266-01 + shipping. Maybe you could find someone that ordered more than they needed after the units ship (should be by the end of this month).


Reply
Posts: 1344
(@mrsmoofy)
Noble Member
Joined: 12 years ago
4586shaggy wrote:My bad. Was looking on my phone. Text was funny

No problem it's a LONG list of info about that item. Depending on how many floods he needs to power.

Controller $39.99 http://www.holidaycoro.com/DMX-to-SPI-Smart-Pixel-Decoder-Controller-p/614.htm
Weatherproof housing $4.29
12v 3.75amp 45w power supply $13.95

$58.23 at the cheapest.

If you need more power

12v 33amp 400w $28.99

Both power supplies are rain proof.

$73.27

Plus what you spend on any wire, connectors, etc.

Either way under $100


Reply
Posts: 98
Topic starter
(@ronaldpa2)
Estimable Member
Joined: 12 years ago
MrSmoofy wrote:No problem it's a LONG list of info about that item. Depending on how many floods he needs to power.

Controller $39.99 http://www.holidaycoro.com/DMX-to-SPI-Smart-Pixel-Decoder-Controller-p/614.htm
Weatherproof housing $4.29
12v 3.75amp 45w power supply $13.95

$58.23 at the cheapest.

If you need more power

12v 33amp 400w $28.99

Both power supplies are rain proof.

$73.27

Plus what you spend on any wire, connectors, etc.

Either way under $100

Wow thanks. I have about 8 floods. This should work...


Reply
Page 2 / 4
Share: