Another pixel contr...
 
Notifications
Clear all

Another pixel controller

292 Posts
18 Users
0 Reactions
81.5 K Views
Posts: 313
Topic starter
(@ee351)
Reputable Member
Joined: 13 years ago
[#31012]

Hi all,

I am developing a new pixel controller based on the parallax propeller protoboard and ENC28j60 Ethernet controller. I wanted to have this controller be cheap enough for users who don’t have large display budgets (cost is approx $30 to assemble). My initial tests using xLights shows that this controller can receive approximately 5 universes of pixel data and output to 12 separate pixel strings at a 50ms refresh rate (850 pixels total). I plan on using simple screw terminals to connect the data/ground conductors of the pixels strings to the controller.

The source code can be found on the Parallax forum. I would post a link, but I can’t yet due to being a new user. Just use the search tool on Parallax’s forum with “WS2812 ENC28j60” in the search. I have the same name on their forum as well. If there's enough interest, I'll provide "a how to assemble" guide based from my work.

pros:

Cheap cost.
Board can be repurposed for other electronic projects during off season.
Design can be modified by end user (e.g. change the terminal type for connecting pixel strings).
Source code available for anyone who wants to modify/improve it.
Easy to build since some of the components are already mounted on propeller protoboard.
Cheaper to have spare controllers on hand in case of failure.

cons:

Uses ENC28J60 10base-T Ethernet chip (this may not be an issue unless the user has a really high pixel/channel count).
Not as refined as other controllers, uses generic propeller protoboard and wire jumpers instead of board traces to make connections.
No web interface, changes need to be made in source code to change pixel configuration.
Currently only works with WS2811/WS2812 pixels (I plan on adding a few others later on like GECE).
Currently only supports unicast.
Power to pixels strings not provided on the pcb.


291 Replies
Posts: 313
Topic starter
(@ee351)
Reputable Member
Joined: 13 years ago

I have improved it a bit more, it can now output data for 1008 pixels across 18 outputs at a 20hz rate.


Reply
Posts: 313
Topic starter
(@ee351)
Reputable Member
Joined: 13 years ago

Radio shack currently has the parallax propeller quickstart boards on clearance for $7.47 each. This board can be used to build this controller.


Reply
jklingert
Posts: 1767
(@jklingert)
Noble Member
Joined: 16 years ago

Here is the link to the code over at the Parallax Forum


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Nice work. There is a lot going for using ethernet as the primary interface. Add isolation to your pros list. And simply off the shelf wiring (like most of the other controllers here).
Lan switches are so cheap to.

Sent from my SM-N9005 using Tapatalk


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Maybe you could go old school and add a switch to select the universe and or string type.

Sent from my SM-N9005 using Tapatalk


Reply
Posts: 353
(@bigredsoftware)
Reputable Member
Joined: 15 years ago
EE351 wrote:Radio shack currently has the parallax propeller quickstart boards on clearance for $7.47 each. This board can be used to build this controller.

Thanks for the tip, I couldn't resist at that price.


Reply
Posts: 313
Topic starter
(@ee351)
Reputable Member
Joined: 13 years ago
Matt_Edwards wrote:Maybe you could go old school and add a switch to select the universe and or string type.

Sent from my SM-N9005 using Tapatalk

At this point, I'm trying to keep it as simple as possible. This controller will definitely be "no frills" but the trade off will be price. If you can snag a quickstart board from RadioShack, you can build this for less than $20. I'm hoping to post some pictures/videos this weekend of the work I've completed so far. Also, I want the code to be available to anyone who may want to improve or modify it for their use.


Reply
Posts: 313
Topic starter
(@ee351)
Reputable Member
Joined: 13 years ago
bigredsoftware wrote:Thanks for the tip, I couldn't resist at that price.

It is a good price, considering that parallax normally sells these for $35 plus shipping.


Reply
dlovely
Posts: 3167
(@dlovely)
Famed Member
Joined: 17 years ago
EE351 wrote:It is a good price, considering that parallax normally sells these for $35 plus shipping.

I picked up 3 of these when they were clearance at $20 figuring they would not go below this when Ken said that already was well below the cost they sold them to RS at.


Reply
Page 1 / 30
Share: