Amps per Pixel Math
 
Notifications
Clear all

Amps per Pixel Math

6 Posts
4 Users
0 Reactions
4,061 Views
Posts: 654
Topic starter
(@szaske)
Noble Member
Joined: 14 years ago
[#30998]

I'm trying to determine how much power these pixels use and how many pixels I can safely connect to my Sandevices controller. Each Sandevices port has a 5 amp fuse. But how many amps does a typical WS2811 or WS2812B LED require? I don't see the data in the Wiki, and I'm not sure how to read the datasheets listed. Looking over the WS2812 PDF can I find out how much current the part needs? I see 20mA per color, so does that mean showing white would use 60mA of power per pixel? Has anyone calculated this?

-=Steve


5 Replies
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago

DIYLEDexpress calls out 3.2A per string, so a 150 pixel (5m of 30LED/m) strip calculates to 3.2A/150LED = 21mA per LED (so I believe 21ma for all three being on to make white).

Electrified3 did some empirical testing a little ways back that showed the numbers to be slightly higher: http://doityourselfchristmas.com/forums/showthread.php?31735-Pixel-Strip-Matrix-Design-Review&p=317392#post317392

And keep in mind that this is for strips, if you go to strings, the current draw will be higher still due to the losses in the wire being greater.


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago
szaske wrote:... I see 20mA per color, so does that mean showing white would use 60mA of power per pixel? Has anyone calculated this?-=Steve

Yes, 60ma per pixel, where each colour draws 20ma for full ON. You may have some current variation due to power supply output voltage.
When choosing a power supply allow for 15% to 20% "slop" so that you don't drive it full bore. If you plan to expand then factor in the additional load, assuming you want one power supply to provide it all.
The voltage will need to match your string, e.g. 5V, or 12V, or...etc.


Reply
Posts: 1133
(@toozie21)
Noble Member
Joined: 19 years ago
LightUp wrote:Yes, 60ma per pixel, where each colour draws 20ma for full ON. You may have some current variation due to power supply output voltage.
When choosing a power supply allow for 15% to 20% "slop" so that you don't drive it full bore. If you plan to expand then factor in the additional load, assuming you want one power supply to provide it all.
The voltage will need to match your string, e.g. 5V, or 12V, or...etc.

So to make sure I am understanding right, you are saying a 5m, 5V, 150 pixel strip (I am still waiting on mine to come in to actually do some testing) would be 60mA per pixel for while, so 60ma*150=9A @5V (45W) for an entire strip?


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

Based on the numbers you provided, that looks about right. (3xmAperPixel) x # pixels = (3x0.020) * 150 = 9A

Most strips that I have been playing with, it was 10 pixels per meter (approx 4"), so a 5M length was (.020x3)x10 x5 = 3A

toozie21 wrote:So to make sure I am understanding right, you are saying a 5m, 5V, 150 pixel strip (I am still waiting on mine to come in to actually do some testing) would be 60mA per pixel for while, so 60ma*150=9A @5V (45W) for an entire strip?

Reply
Page 1 / 2
Share: