Did an 8 channel test tonight. The power supply is simply an 8 Amp fullwave rectifier bridge off of a 220VAC transformer, no storage capacitors.
The camera lens causes the flash to appear low on the screen. The strobes are actually at the top of the screen (the eight black blobs).
I was looking more for the super bright LEd that was used. 300 V is more than I really want to play with.
Jeff C
jcoll549 wrote:I was looking more for the super bright LEd that was used. 300 V is more than I really want to play with.Jeff C
I think a flashlight (torch) LED is all you will find. I did run across a "flash" LED that looked like an array of these LEDs (12 to 18 bright LEDs).
I tried to incoporate a Radio Shack strobe into my display last year but it got lost and was too dim compared to the rest of the lights. If you use any strobe or LED you should place them in a dark area so they will be seen.
I assume that if I set up 100 of these strobes it will be noticed.
Again, there is nothing that will compair against a plasma arc flash (strobe).
Waterproofing
Sorry, this is long winded but this is almost a "How to".
I have been working on a few methods to waterproof the strobe units. I found that some of the disposable camera flash units did not have lenses therefore exposing the reflector that conducts the very low power 4000 volt pulse to get the plasma arc started in the strobe bulb. I have discarded the units without lenses.
The Units I purchased from The Electronic Goldmine had lenses but I have run across a couple that did not work so I test each one using the 1.5 volt AA battery before beginning the modification.
After testing the unit with a battery, the first step is to discharge the capacitor by flashing the unit and then shorting across the capacitor. Then cut off all the unneeded hardware (battery holder, charging switch SW1, and trigger leads noting where the trigger leads are connected). Then carefully bend the capacitor leads so the capacitor is close to the board if required.
I am using 6 conductor 24 gauge telephone wire from Lowe's. I solder two wires to the negative side of the camera flash unit capacitor and connect them to the negative side of the 300 vdc power supply (green and yellow).
I solder two wires to the positive side of the camera flash unit capacitor (white and blue). On the other end of the white and blue wires I attach a 2 watt 820 ohm resistor and connect the resistor to the positive side of the 300VDC power supply. I first tried to put the resistor on the flash unit but if you flash many times in a few seconds the resistor can get hot so it needs to be in open air and not thermally insulated.
I solder the red and black wires to the trigger connections on the board(SW2). It is easier than stripping the wires and soldering to the wires and insulating the connections.
I then again test the unit for proper operation by turning on the 300 VDC power supply and shorting the red and black wires together. My 300vdc power supply is simply a diode bridge connected to 220VAC transformer. After testing the unit, I turn off the power, flash the unit, and short across the capacitor to avoid shocking myself.
Waterproofing:
I tried several different methods:
Fiberglass resin - I poured it over the unit until it started to gel. It looked good but was not perfect and the 300 vdc power shorted out. I tried a couple of times but it was not easy or successful. I did not try to make a mold and "pot" it.
Plasti Dip (for tool handles) - I had to dip the unit several times with 30 minutes between dips. I had trouble covering all the voids and crevices. Now I have pockets of undried Plasti Dip and it still has not dried. This method was quite time consuming but still might work.
Silicone sealant - Masked off the lens, which was not really required since you can control where the silicone goes. I grabbed a tube of silicone and smeared it real good until I saw no parts other than the lens. I allowed the silicone to dry overnight. This worked perfectly and was fast and easy. Large cauking tubes of silicone can be found at Lowe's, Home Depot, or the hardware store. Latex caulking might even work.
The video is of a unit flashing underwater.
OMG!

Looks really nice,..... scary...but nice.
I think I saw an earlier version in Dr Frank-n-furter's Lab on Rocky Horror Picture Show 😉
I think i saw that in "Die hard"
Don't cut the red wire, or was it the black, hmmmm
Let's you get that one on an airplane. 😆
Firegod; Nice work so far. I tryed high power LEDs and over drived them but still not the same as a flash bulb. Unless you use 25 or so.
One warning about the silicone glue it will react with the copper and corrode. The ones you made may not last to long. You may be better off with a conformel coating that thay use on PC boardes if you can find it. AI



