A bit of an update:
The SCR must be within 6 feet of the strobe unit to work. If there is more wire than 6 feet, it will not trigger every time.
I also added a fuse to the charging circuit on each strobe to prevent a meltdown.
FireGod,
Why not build a high current 1.5V power supply, and use the charging circuit already on the camera board?
The on board circuit has a low current/high voltage transformer to charge the capacitor. It only charges at one rate....slow.
I am able to get at least one flash per second with the external 330VDC power supply. The flash rate is only limited by the 820 ohm charge limiting resistor.
If one flash every 10 seconds is OK with you then a large 1.5VDC power supply would be the way to go.
Hi FireGod,
I know this thread s quite old but i was wondering if you had any pictures of the final design/layout, or if you had any detailed documention of the design.
Thanks
docjon wrote:Hi FireGod,I know this thread s quite old but i was wondering if you had any pictures of the final design/layout, or if you had any detailed documention of the design.
Thanks
I am still having trouble triggering the strobes. The SCR does not trigger the strobe every time where a mechanical switch will do it.
My first batch of eight worked perfectly but the second batch of 32 did not. I don't knnow what I did differently on the second batch. SCR too slow switching? I still don't know.
Is this going to be something you will try and solve?
I have been working on this again. I have found that cheap units don't work. Those from the Electronic Goldmine don't work well. I also tried a Select Brand from Walgreens and it did not work either. I have 6 Polaroid units that work and I bought a Kodak disposable unit and it works also.
I'm not sure what the difference is between the units. There is a small capacitor that charges and when the unit triggers, this cap discharges through a 4000 volt transformer which gets the plasma stream inside the strobe tube going. This small cap may be too small, the transformer may be inferior, the construction of the strobe tube may be poor, I just don't know.
I do know if I buy name brand disposable flash units (new) they work no matter how long the lead wire. I have one lead wire that is about 15 feet and it works well.
I am using SCR's to trigger the strobe but a triac might work. For that matter a triac driver might work, I have not tried either one yet. I do know what ever is used it need to be very fast.
Yes same problem here, what ever is placed across sw triggers flash and prevents charging. Even tried germanium based components, ( less leakage ) I have six at the moment powered from the 5volt cat line down to 11/2v as I have said before through an Lm317 IN REVERSE. And 5v relays for the switch but that can add up. 20 strobes at $4 relay whooo. My turn round time between flash is about 3seconds, thats good enough for me, I will only be using them for a final flash.
I have a 110vac/220vac transformer and I use a full wave rectifier to charge the capaictors to 8 strobes. Using a 820 ohm 2 watt charging resistor, they will flash as fast as you want.
The 600 volt 6 amp SCRs work for triggering but you have to purchase name brand camera units.
I bought 140 units from The Electronic Goldmine and built up 32 including waterproffing only to find out they don't work.
FireGod wrote:I have a 110vac/220vac transformer and I use a full wave rectifier to charge the capaictors to 8 strobes. Using a 820 ohm 2 watt charging resistor, they will flash as fast as you want.The 600 volt 6 amp SCRs work for triggering but you have to purchase name brand camera units.
I bought 140 units from The Electronic Goldmine and built up 32 including waterproffing only to find out they don't work.
Yes sir I did read this before, just agreeing with you. My thoughts on this matter is that the switching transistor on board is very sensitive had I more time this is were I would "play around" or am I of my trolley!
