Tree Dazzler is it ...
 
Notifications
Clear all

Tree Dazzler is it hackable ?

63 Posts
19 Users
0 Reactions
35.1 K Views
Posts: 843
(@captainmurdoch)
Prominent Member
Joined: 14 years ago

Hmm, I should have thought of the price match. My local HD was still only down to 75% off on Saturday and the initial price was $39.99 so still $9.99 on clearance. They only had a few left, I think they shipped them elsewhere or hid them because a week earlier they had 50-70 at least.

Bed bath and beyond had about 150 of them when I was in there a week and a half ago but they were still $19.99 there. I wonder if they price match. Google, here I come.....

EDIT: looks like BB&B does but not on clearance items.


Reply
Posts: 3
(@nallen9)
New Member
Joined: 10 years ago
CaptainMurdoch wrote:Hmm, I should have thought of the price match. My local HD was still only down to 75% off on Saturday and the initial price was $39.99 so still $9.99 on clearance. They only had a few left, I think they shipped them elsewhere or hid them because a week earlier they had 50-70 at least.

Bed bath and beyond had about 150 of them when I was in there a week and a half ago but they were still $19.99 there. I wonder if they price match. Google, here I come.....

EDIT: looks like BB&B does but not on clearance items.

they are down to $2 at walmart here

Sent from my SAMSUNG-SM-N920A using Tapatalk


Reply
Posts: 582
(@jimboha)
Honorable Member
Joined: 12 years ago

I picked up 3 dazzlers. Hacking was simple, but I did not use the internal controller or relays (all surface mount, tedious to re-work). I now have a dumb-pixel-like small spiral mega trees. I know - not very creative. But it's what my wife wanted.

I cut off all the strings (8 each, with 8 bulbs), and re-soldered into 10 strings, 8 longer for spiral strings, and two shorter - one for post center and one for a star topper. The spacing on the originals was 8" or more on each string, so I folded the strings over and zip-tied so the bulbs are now 4" apart, still 8 strings. The plastic covers are not water tight, so I thinned some shoe-goo (with Goof Off) and with a fine-needle applicator, flowed glue into the top and partial bottom openings and along the seam. I hope to have added some water resistance, but likely will have long-term issues. I have sufficient length that I can spiral the strings one time around the tree.

I had a Renard Plus RGB+W controller PCB on-hand, so I soldered it up and programmed it with DMX fw. Each channel control 4 colors, while the dazzler strings only have 3. So I plumbed each connector to one string and harvested the extra, or 4th, wire and re-combined into two more RGB lines - one for a center-post string and another for the star topper. I stole a 8" clear plastic start for an old incan spiral tree and spray painted it lightly with flat white paint to make it somewhat diffusive.

I started trying to use the old tree metal framework, but it is not heavy enough to support everything, so I've been modifying it into a new structure. It is about 7ft tall.

Sadly I did not document much of the process. I did, however, take a cool-looking picture of the wiring harness I made: it is basically 8 RJ45 break-out boards all stuffed INSIDE one of the plastic, green, topper-rings. It all just barely fits! I could have saved room by omitting the RJ45 connector and direct soldering the CAT5 to the little PCB, but I like being able to change out the cat5 when the retaining tabs get broken off.

New Dazzler top small

I'll grab more pictures later if I can.

It is a little sad to have nothing more than a jumbo tree dazzler sans actual tree. But it does have good visual impact and the re-programming is looking good.


Reply
yohan
Posts: 85
(@yohan)
Trusted Member
Joined: 13 years ago

double post, deleted


Reply
yohan
Posts: 85
(@yohan)
Trusted Member
Joined: 13 years ago

@jimboha Do you have video of being used.


Reply
Page 11 / 13
Share: