help needed
 
Notifications
Clear all

help needed

66 Posts
10 Users
0 Reactions
16.1 K Views
Barnabybear
Posts: 1583
(@barnabybear)
Noble Member
Joined: 15 years ago
wilky37 wrote:hi, in answer to the above question , yes we have put the dip switch to position 10 ,and all the test patterns work fine, i have been told that these boards are rubbish and never work, hope this is not the case as i have just ordered more and i have quite a few dumb rgb nodes that i want to use, and no i am unable to connect to the bridge web page , i have tried to reset and followed all the instructions, getting frustrated, just hope its something i have done wrong not that the board is not good, if it is this type of boards rubbish what could i use for dumb rgb nodes i am planning to have singing faces in my display , once again thanks

Hi wilky, from what I've read you purchases look good and should play together (I'm guessing you've done lots of reading). You've done the same as I have in the past - plug everthing in with the settings that you have spent hours reserching and -------- it doesn't work (sometimes it does).
If this was my post I'd split things down to each element in the chain.
We know x-lights, but link the web to the bridge you using & you have already linked the board - then we know what you playing with.
Start with one RGB strip (if you can drive one you can drive a hundred).
Chat / post to get x-lights setup.
Get the coms with the bridge working.
Tie in the board.
Then 🙂


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

Wilky if you have or can download team viewer too your computer someone can connect with you and help figure things out team viewer allows the person too see your computer and if both have mics and speakers you can talk back and forth I use this a lot too help others setup things Al just south of me ran a bridge and the same dmx controller this yr and it ran great so just think it is getting things set right with computer too bridge too controller and you will have the flashy you are looking for


Reply
Posts: 48
Topic starter
(@wilky37)
Trusted Member
Joined: 11 years ago

hi thanks for all the great and helpful replies, first sorry if i have posted in the wrong section, just i am using lights so thought id post here, i will move or restart the thread if i have made a mistake, the bridge is connected to the pc with an ethernet cable on the back of the interface a small green light lights up which i believe indicates its receiving a signal. when i turn it on the dmx light flashes twice and then the purple web light will come on, this stays lit for long periods but will then go off sometimes, i have tried to reset it and tried to access its web bag with its ip address 192.168.1.206 but it always says can't connect, i have 3 computers (2 pcs and a mac) all with lights on and i have tried to connect with each computer but none will open it, i was hopeful that it would still work with the default settings, i.e. port 1 is universe 1 so tried to connect it to my board, i do have team viewer installed on the pc and would be extremely great full if someone could help, only problem is the time difference i an in the UK but that could be sorted if anyone would help, thanks in advance Ian


Reply
TazChaLet
Posts: 3042
(@tazchalet)
Famed Member
Joined: 13 years ago

I had problem with my e682 my ips are 192.168.0.??? and it is set factory with 192.168.1.206 I had too force it too use 0 instead of 1 the wiki shows something about forcing it too use a dhcp ip not sure if that is what you need too do with it so you can get into it and change it too maybe 0 like I had too with the e682


Reply
gassy
Posts: 548
(@gassy)
Honorable Member
Joined: 17 years ago

Sounds like you're going to have to get the bridge in the same IP address range as your network. Do you know what IP address any of network devices are using? The bridge is currently using 192.168.1.206 - correct? Do you have a link or info about the bridge?


Reply
Page 4 / 14
Share: