It was reply #3 in this thread that I'm sure gave him the idea that board might be rubbish. It was only talking about one of the two boards he has though. AAH is a pretty good source of information on that forum and is a board designer so it wasn't coming from just a random user comment.
http://auschristmaslighting.com/forums/index.php/topic,8580.msg76916/topicseen.html#new
gassy wrote:Sounds like you're going to have to get the bridge in the same IP address range as your network. Do you know what IP address any of network devices are using? The bridge is currently using 192.168.1.206 - correct? Do you have a link or info about the bridge?
Yes, Wilky, what is your home network range? you may need to set one of your PCs to a static IP in the same subnet as the bridge (192.168.1.50/255.255.255.0) to be able to connect, then change the bridge's IP to match your home network.
Hey Wilky,
You supplied a link to the DMX controller. That was helpful.
I assume you are using this E1.31 Bridge. Is that correct?
You say you cannot access the bridge webpage. Let's focus on that.
Does one of these pictures represent your setup?
Do you know how to find or assign IP addresses?
Are you familiar with DHCP?
What is the IP address of the computer?
What is the IP address of the E1.31 Bridge?
Are you using a network router or a network switch in your setup? If yes, what is the make/model of the router/switch? (I hear gigabit speed devices can cause problems).
If you are connecting the bridge directly to your computer with no router or switch, I -think- you will have to use a "crossover" cable" (I do not know if the bridge or computer auto-sense the connection type or not). Do you have an ethernet crossover cable? If you don't know what that is, you don't have one.
wilky37 wrote:hi thanks for all the great and helpful replies, first sorry if i have posted in the wrong section, just i am using lights so thought id post here, i will move or restart the thread if i have made a mistake, the bridge is connected to the pc with an ethernet cable on the back of the interface a small green light lights up which i believe indicates its receiving a signal. when i turn it on the dmx light flashes twice and then the purple web light will come on, this stays lit for long periods but will then go off sometimes, i have tried to reset it and tried to access its web bag with its ip address 192.168.1.206 but it always says can't connect, i have 3 computers (2 pcs and a mac) all with lights on and i have tried to connect with each computer but none will open it, i was hopeful that it would still work with the default settings, i.e. port 1 is universe 1 so tried to connect it to my board, i do have team viewer installed on the pc and would be extremely great full if someone could help, only problem is the time difference i an in the UK but that could be sorted if anyone would help, thanks in advance Ian
wait a sec. yuou plugged the bridge directly into the computer? the bridge has a default address but the computer does not. you need to set the ip address on the port the bridge is connected to with an ip address in the same subnet. in this case 192.168.1.200 would work. then you should be able to connect
hi sorry for the lack of replies the time difference is difficult, to answer some of the comments here is a link to the bridge that i bought,
today my second board that i had ordered has arrived and that to won't work, so making me think its the bridge, to answer some questions, no i don't know how to assign an ip address , the bridge is plugged straight into the computer and its with a straight ethernet cable not a crossover cable
the above comment
need to set one of your PCs to a static IP in the same subnet as the bridge (192.168.1.50/255.255.255.0) to be able to connect, then change the bridge's IP to match your home network.
I'm sorry but don't understand how to do this
i do apologise if my lack of knowledge is causing the problem, quite prepared to go and find how to do the things that are being suggested just need to be pointed in the right direction Thanks Ian


