Need Help with Smal...
 
Notifications
Clear all

Need Help with Smaller Mega Tree

11 Posts
7 Users
0 Reactions
5,422 Views
Posts: 110
Topic starter
(@todd1814)
Estimable Member
Joined: 11 years ago
[#42695]

I'm trying to build a tree that's not as big as the mega trees I've seen but it's not a mini either. It's a 400 pixel tree with 8 strings, each folded over for a total of 16 strands. The topper will have 50 pixels. I have the controllers and lights and I'm working on getting the power supply, pig tails and pixel strips.

I went to Lowes yesterday with some ideas on what I needed and quickly got confused. I had just reviewed the JUMP and ASAP Poles and looked at the boscoyo tree topper. The tree topper attaches to 3/4" conduit, which seems too small for the whole tree. The JUMP and ASAP Poles use an EMT "Bushing", which I couldn't find in the store.

Ideally, I'd like to install a pipe into the ground (w/concrete) and slip the tree pole into it. I can't figure out what hardware to buy and how to put this together. The pole has to be longer than 10' because the tree is about 10' overall and the pole has to anchor in the ground. I've done a lot of reading but still can't figure out how to get this done. I thought the hardware would be the easy part!

Attached is a drawing of what I came up with. Some of the dimensions are a little off so they have uneven numbers. It's very close overall.

Some general dimensions:

25 Pixels per string at 3" spacing - total strip length = about 80"
Tree Height (Pixel strip area) 72"
Diameter 60"
Star 23" across

MyPixelTree

10 Replies
Posts: 205
(@barlav)
Estimable Member
Joined: 11 years ago

Have you considered building the portable hole II? http://www.magicchristmasnews.org/portable%20hole%20ii.pdf


Reply
Posts: 114
(@dmpeaceman)
Estimable Member
Joined: 16 years ago
todd1814 wrote:I'm trying to build a tree that's not as big as the mega trees I've seen but it's not a mini either. It's a 400 pixel tree with 8 strings, each folded over for a total of 16 strands. The topper will have 50 pixels. I have the controllers and lights and I'm working on getting the power supply, pig tails and pixel strips.

I went to Lowes yesterday with some ideas on what I needed and quickly got confused. I had just reviewed the JUMP and ASAP Poles and looked at the boscoyo tree topper. The tree topper attaches to 3/4" conduit, which seems too small for the whole tree. The JUMP and ASAP Poles use an EMT "Bushing", which I couldn't find in the store.

Ideally, I'd like to install a pipe into the ground (w/concrete) and slip the tree pole into it. I can't figure out what hardware to buy and how to put this together. The pole has to be longer than 10' because the tree is about 10' overall and the pole has to anchor in the ground. I've done a lot of reading but still can't figure out how to get this done. I thought the hardware would be the easy part!

Attached is a drawing of what I came up with. Some of the dimensions are a little off so they have uneven numbers. It's very close overall.

Some general dimensions:

25 Pixels per string at 3" spacing - total strip length = about 80"
Tree Height (Pixel strip area) 72"
Diameter 60"
Star 23" across

I threw your dimensions together in a mega tree simulator. Should help you visualize your project. Scroll down the page to see power requirements, and exact measurements.

Check it out:

https://www.lightshowhub.com/tools/mega-tree-calculator?nm=My%20Mega%20Tree&ph=73.1875&va=180&td=12&bd=60&ns=16&ls=3&ts=4&bs=1&lt=pixel&cpl=3&v=12&ma=50&w=350&pm=80&bcl=rgb(34%2C%2053%2C%20110)&pcl=rgb(0%2C%20153%2C%20255)&ecl=rgb(221%2C%200%2C%200)&evcl=rgb(0%2C%20153%2C%200)&scl=rgba(255%2C%20153%2C%200%2C%200.39)&secl=rgb(255%2C%20190%2C%200)&ant=ramp_white


Reply
stallionent
Posts: 1460
(@stallionent)
Noble Member
Joined: 13 years ago

Check out my Thread for info. Mine is 20 strands, 50 pixels up and 50 pixels down. I used a top rail of a chain link fence. No power injection.

http://doityourselfchristmas.com/forums/showthread.php?42600-Project-180-x-10-ft-Mega-Tree&highlight=project+mega+tree


Reply
dgirard
Posts: 337
(@dgirard)
Reputable Member
Joined: 17 years ago

I'm in process of testing a similar setup...
30 pixels 3" spacing
24 total strips (360)
50 pixel star
I'm calculating the total weight of the pixels/strips at approx 20 lbs. 3/4 EMT should be fine. My plan is to go straight to the ground with my strips..so that leaves me with enough on a 10' piece of EMT to be able to set it into the ground. Otherwise, the fence rail is a great option.

I'm using the boscoyo kit with topper and guy wires. It also comes with a base that you set on the ground and set your pole on (no need to sink a pipe for a 10' tree in my opinion) I'm also going to permanently mount the strips (well, zip tie anyway) before standing the pole up...it should be light enough to do this (I'm almost done assembling the first one--I'm building 2 of these--so I'll be testing the process of standing it up next week hopefully) If it all works, a little pallet wrap should be all it takes to pack it up at the end of the season for next year! (that's the plan anyway)

With the permanent installation, I'm also intending to just hardware my controller connections (I'll have an 8 channel controller mounted to the pole) and avoid needing waterproof pigtails for these.

FYI I'm also building a 30' tall main mega-tree (increase from last years 20')...for that I'm having some of the same dilemma thoughts you've been having...jump pole? Fence rail? pully system?

Either way, I think you'll be fine with the 10'er....I'll take some photos when I do my test install if it helps.

David


Reply
Page 1 / 3
Share: