all right i am creating a mega tree although its not going to be so mega but its a start i guess:)...it will be roughly 8' tall given my string (lighted length is 18.7') i am going to use 12 strands red, 12 strands green , and 12 strands white (all LED). i know its not going to be much because its only 36 channels total.
I was planning on using each string of lights and folding it over to simulate 2 strands (kinda where i got my only 8' tall tree calculation.)
So for my main concern is how about frame ideas the top piece the center support/s and the bottom piece ...i will most likely be mounting a ren16 and ren 24 in the inside of the tree. ANy advice or pictures would be greatly appreciated.
thank you !
Your setup is exactly what I used for the last couple of years - an 8-9' tree with 12 each RGW strands folded over. You can see it built HERE. I used two 10' sections of PVC and cut them up to make an "H" base using three T's - very easy to set up and very stable for it's size. I don't have a close-up of the topper but it's something I stole from Dirknerkle a while back - it's a 2" adapter and holes drilled in and eye-hooks to hold the strings. I just used tent stakes to hold the strings down. I don't have any guy wires but it would be easy to add if you want to. I used a Lynx FreeStyle driving three 12-channel SSR boards but a Ren24 + Ren16 would work well with a couple spare channels to drive a topper or just be spares in case of failures (highly recommended).
budude wrote:Your setup is exactly what I used for the last couple of years - an 8-9' tree with 12 each RGW strands folded over. You can see it built HERE. I used two 10' sections of PVC and cut them up to make an "H" base using three T's - very easy to set up and very stable for it's size. I don't have a close-up of the topper but it's something I stole from Dirknerkle a while back - it's a 2" adapter and holes drilled in and eye-hooks to hold the strings. I just used tent stakes to hold the strings down. I don't have any guy wires but it would be easy to add if you want to. I used a Lynx FreeStyle driving three 12-channel SSR boards but a Ren24 + Ren16 would work well with a couple spare channels to drive a topper or just be spares in case of failures (highly recommended).
very nice ! i am going to be elevating this tree in a more visible spot so i am going to need a base frame (cant use tent stakes but if push comes to shove i will have to rethink that and go with the easier approach 🙂 ) i was almost thinking of suspending it but still open to ideas, but great to know that you had success with a similar channel setup and height.
I also did much the same thing, although I used a 10' length of 3" black PVC as the pole and mounted the topper star on that. Doubling-up the strings works very well -- this has only 24 strings around the base which doubled-over makes 48 verticals and fills out the tree pretty nicely. I added 12 channels of white on the pole so the whole thing uses 24 channels around the tree, 12 channels on the pole and 1 channel for the star topper. An SS24 and SS16 did the job nicely with a few spare channels for reserve...
dirknerkle wrote:I also did much the same thing, although I used a 10' length of 3" black PVC as the pole and mounted the topper star on that. Doubling-up the strings works very well -- this has only 24 strings around the base which doubled-over makes 48 verticals and fills out the tree pretty nicely. I added 12 channels of white on the pole so the whole thing uses 24 channels around the tree, 12 channels on the pole and 1 channel for the star topper. An SS24 and SS16 did the job nicely with a few spare channels for reserve...
good idea ...so what was the piece used at the base or (Sleeve) i am kinda thinking along the lines this is the direct i might have to go considering the elevated mounting.
griffixdc wrote:good idea ...so what was the piece used at the base or (Sleeve) i am kinda thinking along the lines this is the direct i might have to go considering the elevated mounting.
Here's how I built a midi-tree and a mega-tree a few years ago. Photos are a little old but you'll see all the parts that made up the construction. The examples were before I started using doubled-up strands, and single-strands are pretty sparse unless you have a lot of channels...
http://www.diychristmas.org/dirknerkle/howto-mega_tree.html
dirknerkle wrote:Here's how I built a midi-tree and a mega-tree a few years ago. Photos are a little old but you'll see all the parts that made up the construction. The examples were before I started using doubled-up strands, and single-strands are pretty sparse unless you have a lot of channels...
as usual great sources of information...i like how you always take the more cost effective approach with some engineering expertise which allows for room to take and expand to everyone's particular needs. i will Mosck this this design with some mod changes. i will also possibly post a follow up on this just in case people need another How to version in the thread.


