LED Matrix
 
Notifications
Clear all

LED Matrix

29 Posts
15 Users
0 Reactions
13.2 K Views
Posts: 1168
(@keith-r)
Noble Member
Joined: 19 years ago

After buying Electric fence wire (aluminum), and picture frame/plant hanging wire (steel), I am eventually going to go back to buy copper wire for the matrix. I have tried different methods of soldering, different temps, and different irons and guns. The solder just won't stick. Flux does seem to help, but doesn't insure a 100% guaranteed solder joint. Better to be safe than sorry.
Keith


Reply
Posts: 87
(@wingrunr)
Trusted Member
Joined: 19 years ago

I drilled out my own masonite board with at #9 bit and then put down copper tape. It goes pretty quickly. The copper tape is designed for shielding bass amps so solder sticks to it instantly. All you have to do is stick and LED in a hole, fold over the leads, and solder. This also makes it VERY easy to replace an LED to goes bad. I'm not very interested in that LEDtriks wrap thing...


Reply
Posts: 150
(@alwysrit2)
Estimable Member
Joined: 19 years ago

Wingrunr,
Where did you find the copper tape? How much was it? How many feet(The tape, not you). So many questions...

As far as what I have used - so far, I used a bare steal wire I bought for $9 for 500' at a local electronics surplus store. It doesn't solder well, but using flex and putting the leads down at an angle has helped.
I do have one hint I haven't seen before: I am currently using 1" pegboard; I start with a pair of LEDs, bending the leads of the LED's at about a 30 degree angle towards each other, then solder them together before soldering them to the common conductor. This helps to hold the leads in place while I solder them to the conductor and gives me 2 connection per LED to the conductor.

Thanks!
-Don

P8270190

Reply
Posts: 121
(@vairmoose)
Estimable Member
Joined: 19 years ago
Reply
cobraman44
Posts: 258
(@cobraman44)
Reputable Member
Joined: 19 years ago

I just extra cat 5 cable I had laying around. Strip the insulation and go. It goes a long way because you get 8 rows per section of Cat 5.


Reply
RJ
Posts: 673
 RJ
(@rj)
Prominent Member
Joined: 19 years ago
wingrunr wrote:I drilled out my own masonite board with at #9 bit and then put down copper tape. It goes pretty quickly. The copper tape is designed for shielding bass amps so solder sticks to it instantly. All you have to do is stick and LED in a hole, fold over the leads, and solder. This also makes it VERY easy to replace an LED to goes bad. I'm not very interested in that LEDtriks wrap thing...

Yes that is the copper tape method I used on the second Ledtriks made. It has held up better that the buss wire one. It is faster and tougher than the wire method.

RJ


Reply
Posts: 352
(@maffeirw)
Reputable Member
Joined: 19 years ago

I used the copper foil tape method to build a 2 panel LedTriks board (16 x 96) and went crazy for over a month trying to get it to work right. Letters were illegible on the few times they scrolled at all. All LEDs in large sections lit when they shouldn't and then other sections didn't light at all. I didn't want to recommend anything I did to anyone because I couldn't tell what was going wrong. I tested all 15 of the MBI chips I had purchased (the Allegros stopped shipping samples when I needed them) and finally, sort of, got 1 of the controllers working (3 working chips out of 15 are terrible odds.) I still had random LED flashes leading the letters as they scrolled and other strange problems but at least I could read most of the letters on the one board. The Allegro samples finally started shipping again and once I installed them in 2 controllers, all the problems resolved themselves on both boards. It was like magic. So now I have no problem recommending the copper foil (and the Allegro chips). I used 1/4" copper foil but I believe that 3/16" would work as well. It can be purchased at any local stained glass supply shop (I paid $8.00 a roll) or you can find the foil cheaper online. The rolls are usually 36 yards long and you will need 3 rolls for two panels. I ran all the cathode lines first then brushed on a hand tool handle dip product that I got at Home Depot at each anode-cathode junction to prevent shorts between the crossing tapes. I then laid the anode foil tape across the cathodes making sure that the tape remained insulated by the handle dip. It was then simple to solder the LEDs in place. Just bend the leads, clip and solder. I mounted the controllers to the back of the LedTriks panel as shown. I have since been looking to buy some additional Allegro chips (I still have 2 more controllers and panels to complete) but can't find anyone who sells them. Please let me know if anyone has found a supplier (preferably in the states).

Copper Foil 1
Copper Foil 2
Copper Foil 3
Copper Foil 4

Reply
Posts: 87
(@wingrunr)
Trusted Member
Joined: 19 years ago

The copper tape from Stewart MacDonald is far cheaper and of higher quality than the copper foil or that stuff from Amazon.

http://www.stewmac.com/shop/Electronics,_pickups/Supplies:_Shielding/Conductive_Copper_Tape.html


Reply
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

The tape at amazon is 3.5mils thick, the tape at Stewart MacDonald is 1.5mils thick.
You also have to read closely to see if you are buying the stuff in Feet or Yards!

My vote is the amazon stuff at this point.

However, I'd also like to point out that Michaels Crafts and Hobby Lobby both carry Stained Glass supplies. They seem to always run a 40% or 50% off coupon each week in the paper and online too in the case of Hobby Lobby. I think I'll check their foil out this week!


Reply
Page 3 / 3
Share: