Walmart 50 led dumb...
 
Notifications
Clear all

Walmart 50 led dumb string

5 Posts
4 Users
0 Reactions
2,048 Views
Posts: 200
Topic starter
(@dstokesdubois)
Reputable Member
Joined: 15 years ago
[#29830]

I bought a string of 50 multi colored led lights at Walmart. Has plugs at both ends. Plugged them into the end of one of my incan, strings to see what they would do. Running a Renard64 with the rezSSRs. Ran a sequence where I ramped on over 4 seconds and then ramped off over 4 seconds. Seemed to work ok except for a slight flicker when it was at its dimmer points. Can they be run this way. I'm just starting to experiment with leds. I have some Ray Wu leds, an E6804 and a power supply being shipped so I can learn with them. Not sure how I can modify these cheap led strings from Walmart to plug into the E6804. Figured these strings would be inexpensive to use for some parts of my light show (walkway fence). Any suggestions would be helpful.


4 Replies
duramadmax
Posts: 904
(@duramadmax)
Noble Member
Joined: 16 years ago

The LED multi color strings are not the "real" dumb strings like RGB strings such as ray wu stuff you used for a controller such as a 6804/681/px1 etc. They are only controllable via a 110v ssr type controller such as your 64 or say a ren24ss. They will flicker due to leds design because they are running on AC current. True dumb strings are 5 or 12 volts DC.

LED bulbs are not constantly on like an Ican bulb. They flicker because they are turning on and off at high rate (60hz) and the human eye can detect that. When they run on DC power, they will not flicker.


Reply
Posts: 24
(@inknown)
Eminent Member
Joined: 17 years ago

Just use them like incans. Like duramanadman said they aren't RGB but can be controlled fine with Renard 64. I used mostly LEDs of this type this year for my display. I use SS24s and they worked fine. If the flicker is a problem convert the strings to full wave, most of the cheap strings are half wave this will help. Their was a group by for a PCB for a converter board before christmas hopefully they will do it again. Also, if they don't dim correctly, add a C9 regular incan bulb to the channel. Fixes a lot of the dimming issues. Just remember they aren't RGB and not for use with the E6804.


Reply
Posts: 200
Topic starter
(@dstokesdubois)
Reputable Member
Joined: 15 years ago

Thank You. This is pretty much what I expected to hear. I heard some good ideas though. These are on sale right now for about a dollar so I figured they would be handy and cheap for some of my display that doesn't do much.


Reply
kidcole
Posts: 307
(@kidcole)
Reputable Member
Joined: 17 years ago
dstokesdubois wrote:Thank You. This is pretty much what I expected to hear. I heard some good ideas though. These are on sale right now for about a dollar so I figured they would be handy and cheap for some of my display that doesn't do much.

Converting the LED strings to full wave rectified is well worth the effort. Many people don't like looking at the flicker .. about 1/3rd of everyone sees it.

There are some tiny circuit boards that will be available here as a group buy in the next month or two, to make really quick full wave rectifiers for your LED strings, with 4 diodes. You can buy 1000 of them for less than $10 including shipping (an eBay link was provided last week). Keep any eye out for the group buy. ... something like 10 cents each little board. There will be plenty of instructions.

BUT if you combine your converted LED strings with incandescents on the same channel, make sure the LEDs are plugged in LAST (assuming you plug them into each other). Or you can split the channel into separate connections, one for LEDs and one for incans. The socket on the end of the rectified LEDs will be 110v DC (not AC). You will quickly let the smoke out of your light string or your rectifier if you plug in incans to 110V DC.


Reply
Share: