Cheap LED Strings
 
Notifications
Clear all

Cheap LED Strings

76 Posts
18 Users
0 Reactions
38.8 K Views
Posts: 11
(@stevexmas)
Active Member
Joined: 16 years ago

hi dirknerkle,
I've got a string of these fairy lights, but there is one difference in how my controller is wired. In your picture (jpeg3 and jpeg4) there is a wire soldered to the first position on the left and the second position on the left. On my controller the two wires are both soldered to the first position on the left, and nothing is soldered to the second position (it is empty). What do you think this means? Would your solder solution still work?
Thanks in advance!

dirknerkle wrote:I love to experiment, and I bought a half-dozen sets of the cheap 100-ct LED strings off eBay that are often described as "fairy lights" or "wedding" or "Christmas" lights. Most of the time these sell for 1 penny plus shipping, and you have to watch the cost of shipping or it'll eat you alive 😕

The lights come with their own controller and multiple blinking/fading options, but there's no way to set it to one type or another. So instead, I decided just to force them to all "on" so I could use them normally. Here's how:

1. Open the case of the controller. Inside you'll find a small circuit board with some diodes and a few other parts. Locate the row of SCRs. They're probably PCR406 SCRs (picture 2). They look like common transistors.

2. Flip the board over and locate the anode and cathodes of the SCRs -- the two front solder pads as in picture 3. (The back pad is the gate).

3. Solder a jumper wire across all 8 of the pads. (picture 4(

4. Reassemble the controller and you're good to go.


Reply
dirknerkle
Posts: 10309
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

I think the bottom line is that there are 5 wires in total. Four of them carry lights, probably 25 lights each; the last is a return wire that connects to the very end of the cord where all 5 wires meet. It's quite possible that the one you have is either not made correctly or is some aberration of the norm (providing there is a norm, of course ;))

Follow the wires from the terminal where two cables are connected, and see where they go. It will take you a while because the darned wired are so tightly twisted, but you can do it. I'll guess that they both are attached to lights within about 6 feet of the controller. If so, the assembler may have soldered it wrong.

If memory serves me right, Christmas-Light (DIYC user name) simply identifed which were LEDs and which was the return wire, and he just chopped-out the controller and connected the 4-wires that are lights to one terminal of the plug and the return wire to the other. It works out because there are 25 LEDs per wire and enough resistors on various LEDs to moderate the current properly.

I experimented by making a full-wave bridge for the lights and then connecting them that way. It worked as well, although not quite as bright as it would have been. The solution to that was to add a somewhat beefy electrolytic capacitor across the rectified terminals of the bridge.

All in all, after all that research and experimentation I'm not even using the darned things this year.

I hate LEDs. They're just putsy to work with, and I'm sure they'd last a long time if I didn't keep experimenting with them and eventually throwing them out.


Reply
Posts: 11
(@stevexmas)
Active Member
Joined: 16 years ago

Hey dirknerkle,
Thanks for the reply! I checked the string and followed the individual LEDs and what I appear to have is THREE wires with 33 lights each (the first and fourth led are on the same wire, the second and fifth, etc). I also ran the string and looked at which lights went on and off and when.
I'm not sure why there is the fifth wire, but that's probably why I have two wires (the returns) soldered to the first position. On my circuit board I only have three of those "things" on the back (and an empty position) where you have four. I wonder if they did this (three circuits instead of four) to save money, and how many pennies they saved...
Anyway, with that in mind, do you think I can still just cut out the controller? Or if I soldered the wire across like you did, would I still do it the same way, or skip the empty position (two spots) and only solder across six?
Actually, I want to use these outside and would probably be better off ditching the non-waterproof controller.
What are the odds that just wiring these together (three on one wire) (two on the other wire) will work?
And will the LED's be less bright then?
Thanks.


Reply
dirknerkle
Posts: 10309
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
SteveXmas wrote:
Anyway, with that in mind, do you think I can still just cut out the controller? Or if I soldered the wire across like you did, would I still do it the same way, or skip the empty position (two spots) and only solder across six?
Actually, I want to use these outside and would probably be better off ditching the non-waterproof controller.
What are the odds that just wiring these together (three on one wire) (two on the other wire) will work?
And will the LED's be less bright then?
Thanks.

Well, one of the beautiful things about DIY with undocumented circuitry such as this is that (1) it's cheap and if it burns up, it's no big deal and (2) you can usually deduce something from the tracings on the small board that's inside the controller.

I'll guess there are four 1N4004 diodes that create a full-wave bridge off the AC power input. There are likely one or two resistors, probably a capacitor, a tiny CPU (on its own circuitboard) and then some small SCRs that go out to the channels. With 33 LEDs per circuit, it's *likely* that they are designed with appropriate resistors to handle 120volts. The voltage at the output of the bridge will probably be in the 100-110vdc range, a resistor and capacitor are there to cut it back to (probably) 5vdc for the little CPU card, and the CPU outputs trigger the gates on the SCRs to let the electricity flow to the outputs. So the output part is basically an SSR while the rest of it is a dual-voltage power supply. The CPU card functions the same as a PIC in a Renard controller.

Leds typically are typically designed for 1.5 to 3v, and so 33 of them in series with integrated resistors indicates it's likely designed to handle the full voltage coming out of the full-wave bridge.

Deducing what is *likely* to happen is one thing, but you really don't know until you try it. If it were me, I'd set it up on the floor of my garage, untangle it so no wires are touching anything, and I'd use a switched terminal strip so I didn't have to be physically holding anything at the time I threw the switch. If I didn't see any sparks and nothing burst into flame, well, then I'd figure that it's probably going to work. If anything started to smoke, well, I'd power it off, unplug it, wait about 5 minutes to make sure nothing was hot and probably throw it away.

If you're looking for a guarantee of some kind that it's going to work, sorry, I can't give you that and I doubt that anybody would. I can suggest things that are *probably* okay, but you're the only one who can see, touch, and look at the tracings on the controller. But with careful thought and technique you can safely try it out. And, luckily, they don't cost a lot so killing one of them doesn't hurt the pocketbook too much.

Isn't playing with electricity exciting? :mrgreen:


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

I think it's a good day when something blows up or catches fire. It helps to break up the monotony of things always going right. Even at work while everyone else is backing up or falling off their chairs as components expand toward a gaseous state, I tend to enjoy the moment and watch the plume as it slowly rises and spreads out when it hits the ceiling.

I still think it's funny that the guy I worked for on my first day of my current job told me not to be afraid to destroy a few parts.:mrgreen:


Reply
Page 10 / 16
Share: