A/C Led Strobes
 
Notifications
Clear all

A/C Led Strobes

13 Posts
8 Users
0 Reactions
8,319 Views
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
[#11721]

Here's a project I've been working on for a while... and the final result. I think it works, but you all can judge for yourselves.

It all started early this spring after I read the LED strobe idea that Brad Jones presented a while ago (link to his posting below)

http://doityourselfchristmas.com/forums/showpost.php?p=112108&postcount=69

In a later posting he wrote "...the 1n4001 diode is only a protection device in-case I did something stupid and throw full wave un-rectified AC at them."

Okay, I thought, I certainly qualify in the stupid category, but why not use that to my advantage?! Why not build strobes with the diode to deliberately be powered by an A/C wall wart to control the voltage? And then, thinking outside the box a little further, I decided to use a regular A/C SSR to control them, but power the SSR with the wall wart which then would fire the strobes.

To take the concept further yet, I took one of my experimental Ren8 boards, coupled that with an 8-channel SSR, connected a Rev-6 RenW to it to make it wireless, powered everything with a single 12vac wall wart and stuck it inside a CG-1000 case.

The video is only 5 seconds long -- I just laid the strobes in the floor and let 'em go for a bit. But this wireless strobe setup will be hanging in one of my trees this year. Here's the link to the video:

http://digwdf.com/dirknerkle/video/led_strobe_test.AVI


12 Replies
Posts: 488
(@dj-merritt)
Honorable Member
Joined: 18 years ago

Nice job Dave ! I have been looking for something like this . I am not sure if it would be cheaper to just pruchase the c9 strobe or this way, What ya think ?


Reply
Posts: 604
(@aussiephil)
Honorable Member
Joined: 19 years ago

Dirk

I have seen Brad's working designs and they have heatsinks on the 317 to combat the heat generated, it's the reason we went to a true constant current design.

Obviously it works, and if used purely to strobe then likely not an issue, however if someone left this turned on in the sequence the 317 is likely to cook itself

Phil


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Hi, Bud!
I suspect that eight C9 strobes are a lot less expensive than this, but on the other hand, these are wireless, can be individually controlled to blink at the interval I need them to blink, and, if I want, I can keep them on and dim them, too. Plus I can use the controller/SSR as a standard 120v system just by powering the SSR with the 120v side of the wall wart instead.

It's actually a little crazy (well, maybe a LOT crazy) to go to all the trouble to kludge this thing together, but I learned a lot in the process and I've got something useful that can also easily be repurposed.

But in this case, I'm pretty sure it'd be cheaper to buy the technology than to invent it.

Phil -- thanks for the reminder about the heat sinks. I do recall seeing them on Brad's design, but I think he was throwing a lot more power at them than I am. Of course, up here in Minnesota it'll probably be below zero (Fahrenheit) outside when we use them, but I've left them on for as much as 5 minutes and they didn't seem to get too hot -- in fact, only slightly warm!


Reply
kwajtony
Posts: 118
(@kwajtony)
Estimable Member
Joined: 17 years ago

I think it is a great concept and obviously will work.


Reply
Page 1 / 3
Share: