Cheap LED Strings
 
Notifications
Clear all

Cheap LED Strings

76 Posts
18 Users
0 Reactions
38.8 K Views
dirknerkle
Posts: 10309
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
[#11728]

I love to experiment, and I bought a half-dozen sets of the cheap 100-ct LED strings off eBay that are often described as "fairy lights" or "wedding" or "Christmas" lights. Most of the time these sell for 1 penny plus shipping, and you have to watch the cost of shipping or it'll eat you alive 😕

The lights come with their own controller and multiple blinking/fading options, but there's no way to set it to one type or another. So instead, I decided just to force them to all "on" so I could use them normally. Here's how:

1. Open the case of the controller. Inside you'll find a small circuit board with some diodes and a few other parts. Locate the row of SCRs. They're probably PCR406 SCRs (picture 1). They look like common transistors.

2. Flip the board over and locate the anode and cathodes of the SCRs -- the two front solder pads as in picture 2. (The back pad is the gate).

3. Solder a jumper wire across all 8 of the pads. (forum won't let me upload picture 4)

4. Reassemble the controller and you're good to go.

cheap 3
cheap 2
cheap 1

75 Replies
ukewarrior
Posts: 4674
(@ukewarrior)
Illustrious Member
Joined: 18 years ago

I got a set of these too to see what they are like.

What about dumping the pcb all together?
Do you think all that would be required would be some diodes wired into the lineset?

dirknerkle wrote:I love to experiment, and I bought a half-dozen sets of the cheap 100-ct LED strings off eBay that are often described as "fairy lights" or "wedding" or "Christmas" lights. Most of the time these sell for 1 penny plus shipping, and you have to watch the cost of shipping or it'll eat you alive 😕

The lights come with their own controller and multiple blinking/fading options, but there's no way to set it to one type or another. So instead, I decided just to force them to all "on" so I could use them normally. Here's how:

1. Open the case of the controller. Inside you'll find a small circuit board with some diodes and a few other parts. Locate the row of SCRs. They're probably PCR406 SCRs (picture 2). They look like common transistors.

2. Flip the board over and locate the anode and cathodes of the SCRs -- the two front solder pads as in picture 3. (The back pad is the gate).

3. Solder a jumper wire across all 8 of the pads. (picture 4(

4. Reassemble the controller and you're good to go.


Reply
Posts: 1041
(@christmas-light)
Noble Member
Joined: 18 years ago

YEP that is one way to do that 😉

Here in Denmark, "real" christmas light is expensive so I brought alot of those lights last year, but I did not do the same as you did, I simpley cutted the 8 ch funktion controller of and then I collected the 3 - 4 wire + into one + and there is only one -, so at this point I have "one" wire + and one wire -

Then I made a full wave rectifier and connectede the + and - and the two wire with AC and it work perfekt, the reason why I did this, is because the wires easy break/fall of and then you can get a electrical schok 😮

C - L


Reply
dirknerkle
Posts: 10309
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
ukewarrior wrote:I got a set of these too to see what they are like.

What about dumping the pcb all together?
Do you think all that would be required would be some diodes wired into the lineset?

That would be a better solution, but the strings have four circuits and each gets about 48 vdc (it varies from 46-48vdc in different strings). I haven't yet figured out how it gets down to that value, but I'm thinking that the resistors may form some sort of voltage divider. (I've seen 1N4004 and 1N4007 diodes in different controllers.) Each circuit has 25 LEDs, so that divides out to about 1.9v each, but there are a few what look like 1/8w resistors soldered to some of the LEDs to probably cut the current a bit. Curiously, they measure about 3k ohms.


Reply
dirknerkle
Posts: 10309
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
christmas-light wrote:YEP that is one way to do that 😉

Here in Denmark, "real" christmas light is expensive so I brought alot of those lights last year, but I did not do the same as you did, I simpley cutted the 8 ch funktion controller of and then I collected the 3 - 4 wire + into one + and there is only one -, so at this point I have "one" wire + and one wire -

Then I made a full wave rectifier and connectede the + and - and the two wire with AC and it work perfekt, the reason why I did this, is because the wires easy break/fall of and then you can get a electrical schok 😮

C - L

What voltage did you give the lights after building the fw rectifier?


Reply
Page 1 / 16
Share: