Can you splice ws28...
 
Notifications
Clear all

Can you splice ws2811 node strings together?

8 Posts
7 Users
0 Reactions
6,776 Views
Posts: 13
Topic starter
(@googlexx)
Eminent Member
Joined: 14 years ago
[#43912]

I have 2 strings of ws2811 nodes at 50 lights each string. I cut half off the first string and then attached them to the second string and it messes up the entire string when I run them. I know the wire order is correct. Are you not able to manually splice pixel strings together?


7 Replies
Posts: 13
Topic starter
(@googlexx)
Eminent Member
Joined: 14 years ago

The first string of 50 loses half its lights and the second string has random colors and turn on and off randomly. But I know both strings work.


Reply
Posts: 486
(@uncledan)
Honorable Member
Joined: 11 years ago

make sure the data path is correct. The nodes should have di for for data in and do for data out on them. I've never wired wrong to know to know what happens but worth a look


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

From the symptoms it sounds like you connected Do to Do instead of Do to Di. The former will leave Di floating.


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago

I had a similar experience, but not in cutting some pixels (haven't done that yet). I didn't know which end was which with regards to the data line. I couldn't read anything on my WS2811 chip. My first for pixels, a week or so ago.
Of course I had to have it backwards first time. My symptom was a few pixels were on in the string but no updates. Once I got the data going to the correct side of the string it worked like a charm. So, like the advice of others, check the data lines as they are undirectional.


Reply
Wolfie
Posts: 2225
(@wolfie)
Noble Member
Joined: 11 years ago

Of course you can splice 2811 pixels together. We do it all the time.

See the tree? Thats 24 strands of 60 pixels each. I cut 50 px strands into groups of 10 and soldered them to the ends of 50px strands to make 60px strands for the tree.

You have to make SURE you follow the data flow path. Power can flow either direction down the wires but data MUST flow only in one direction to make them work.

As stated, pixels have a DI (Data In) and DO (Data Out) connection. When adding onto the end of a string, you must attach DO of the first string to the DI of the second string you are adding. Depending on the node type and maker, there may also be tiny arrows indicating flow direction. In other cases its hard to see anything through the molded plastic. A magnifying glass and slightly wetting the outer plastic sometimes will get you enough visibility to verify direction.

Here is what is in a typical pixel:

Note the arrows and DO. Most of the time DO is on the side with the chip. BUT NOT ALWAYS. Some nodes, especially 12v ones have chips on both sides. One side will be the 2811 chip like in the photo, the back side will have a smaller chip with fewer pins, this is a voltage regulator.


Reply
Posts: 252
(@vincerules)
Reputable Member
Joined: 14 years ago

What size power supply are you using


Reply
codec101
Posts: 355
(@codec101)
Reputable Member
Joined: 13 years ago
Wolfie wrote:Of course you can splice 2811 pixels together. We do it all the time.

Aye, this is the second house my pixels have been on, nearly all of my strings have been spliced at least once, some twice. Make sure they are all good connections, my where all soldered with heat shrink tubing on them. Also you should not just rely on the wire colors! I've had a couple pixels in a string where the wires got flipped during manufacturing and red (normally V+) suddenly became Ground and Blue (Normally Ground) suddenly became V+. Go by the markings on the pixel itself.

IMAG0443

Reply
Share: