Helix Ether-Node Co...
 
Notifications
Clear all

Helix Ether-Node Controller

108 Posts
8 Users
0 Reactions
73.4 K Views
Posts: 947
(@warlock)
Noble Member
Joined: 19 years ago

Plus your e1.31 bridge ahould have status leds to tell you if it is getting aignal


Reply
Posts: 300
(@kiowamike)
Reputable Member
Joined: 18 years ago
Make sure you have an xbee connection between the 2 units. If not then you jave an issue sending the commands between the mainboard and your ethernetnode

Good signal between the 2. AI is flashing on both and RX and TX lights respond accordingly.

Plus your e1.31 bridge ahould have status leds to tell you if it is getting aignal

I assume you're referring to the ACT led. Its blank.

Still solid heartbeat and show stopped on the Ethernode. The HNC is playing the show as it should but no output from the Ethernode. Also no Socket lights illuminate on the Ethernode.


Reply
Posts: 947
(@warlock)
Noble Member
Joined: 19 years ago

Then you have a signal issue. Is your bridge responding ????


Reply
Posts: 300
(@kiowamike)
Reputable Member
Joined: 18 years ago

Here is the config file from the Ethernode maybe this will help?[

2 System Address
1 Baud Rate Index (57600 bps)
1 Communication Mode (XBee (Wireless))
18 MAC 1st octet
52 MAC 2nd octet
86 MAC 3rd octet
120 MAC 4th octet
144 MAC 5th octet
2 MAC 6th octet (matches system address)
192 IP address 1st octet
168 IP address 2nd octet
10 IP address 3rd octet
10 IP address 4th octet
255 Subnet mask 1st octet
255 Subnet mask 2nd octet
255 Subnet mask 3rd octet
0 Subnet mask 4th octet
192 Gateway address 1st octet
168 Gateway address 2nd octet
10 Gateway address 3rd octet
1 Gateway address 4th octet
192 Socket 1 IP address 1st octet
168 Socket 1 IP address 2nd octet
10 Socket 1 IP address 3rd octet
11 Socket 1 IP address 4th octet
0 Socket 2 IP address 1st octet
0 Socket 2 IP address 2nd octet
0 Socket 2 IP address 3rd octet
0 Socket 2 IP address 4th octet
0 Socket 3 IP address 1st octet
0 Socket 3 IP address 2nd octet
0 Socket 3 IP address 3rd octet
0 Socket 3 IP address 4th octet
0 Socket 4 IP address 1st octet
0 Socket 4 IP address 2nd octet
0 Socket 4 IP address 3rd octet
0 Socket 4 IP address 4th octet
5568 Port number
1 Total number of E1-31 frames per event
X Start of XBee Config Commands
17 Number of XBee Config Commands
ATID44f Set PAN ID
ATBD6 Set Baud Rate (57600 bps)
ATMY2 Set Network Address
ATDL1 Set Destination Address to HNC
ATDH0 Set Destination Address High to 0
ATCE0 Set it to be an End Device
ATA16 Configure End Device Settings
ATDA Force the End Device to Disassociate
ATRO0 Set to Streaming Data
ATMM1 Set to no ACK Mode
ATPL4 Set to Max Power Level
ATD51 Set Pin 15 to be AI
ATP01 Set Pin 6 to be RSSI
ATRP5 Set RSSI Timer to 500ms
ATCT000F Set Command Mode Timeout to 1.5 Seconds
ATWR Write Settings to NVRAM
ATCN Exit Command Mode


Reply
Posts: 947
(@warlock)
Noble Member
Joined: 19 years ago

Can't see it as I am on my phone. Lol


Reply
Page 16 / 22
Share: