okay the only way I can get it to work is by downloading the driver for my breakout board and changing the baud rate to 57600 (breakout board baud rate). Vixen and Arduino I had already set baud rate to 57600. Then ever time I hook up I have no problem. Once it is up and running the breakout board can be unplugged and it works fine.To test this theory i used 2 different cpu and got same results. Ive come to the conclusion that my board may be the culprit! I ordered a clone off of amazon and it was suppose to be a specific one. But I got something different then what I ordered. I hope this helps others out, as I struggled for a week or so on this.
I know absolutely nothing about writing code but have successfully re-wrote some of the code here and I now have 16 channels up and running.
It seems I keep finding things I want to do, but have problems installing and executing the software- audacity! Hopefully Ive not rubbed anyone the wrong way with my little rants! lol
keyman6868 wrote:okay the only way I can get it to work is by downloading the driver for my breakout board and changing the baud rate to 57600 (breakout board baud rate). Vixen and Arduino I had already set baud rate to 57600. Then ever time I hook up I have no problem. Once it is up and running the breakout board can be unplugged and it works fine.To test this theory i used 2 different cpu and got same results.....
It doesn't make sense to insert the breakout board and then later remove it and claim it works.
Your sketch is what decides if you need a breakout board. It only works for the MEGA board, or other Arduino boards that have more than 1 internal serial ports.
I suspect that you are using a modified sketch that originally used a breakout board but now is changed so it doesn't.
Can you post your sketch?
// This code was written by Victor Perez for doityourselfchristmas.com based on the code from Zparticle, Si_champion and Neil Tapp.
// To adapt the code to your case, just change this top section, with the #define lines.
// Includes the watchdog timer library
#include
// This sets how many channels will vixen be sending. Can be set to any number from 1 to 48 for Arduino Mega, and 1 to 18 for Arduino Uno.
#define CHANNEL_COUNT 48
// speed for the com port for talking with vixen. From 9600 to 115200. Use the same speed as set in Vixen.
#define VIXEN_COM_SPEED 57600
// Timeout waiting for serial input before going to random mode (in milliseconds).
#define TIME_OUT 10000
// If the relays turn On and Off opposite to Vixen sequence, change "#define MODE NOT_INVERTED" for "#define MODE INVERTED"
#define NOT_INVERTED 0
#define INVERTED 1
#define MODE INVERTED
// which pins control which channels
// You can change these assignment to use different pins, but be very careful to not repeat the same pin number for 2 channels.
// DO NOT use pings 0 and 1, as those are for the serial port to talk to the computer.
#define CH01 2
#define CH02 3
#define CH03 4
#define CH04 5
#define CH05 6
#define CH06 7
#define CH07 8
#define CH08 9
#define CH09 10
#define CH10 11
#define CH11 12
#define CH12 13
#define CH13 A0
#define CH14 A1
#define CH15 A2
#define CH16 A3
#define CH17 A4
#define CH18 A5
// Up to here for Arduino uno.
#define CH19 A6
#define CH20 A7
#define CH21 A8
#define CH22 A9
#define CH23 A10
#define CH24 A11
#define CH25 A12
#define CH26 A13
#define CH27 A14
#define CH28 A15
#define CH29 22
#define CH30 23
#define CH31 24
#define CH32 25
#define CH33 26
#define CH34 27
#define CH35 28
#define CH36 29
#define CH37 30
#define CH38 31
#define CH39 32
#define CH40 33
#define CH41 34
#define CH42 35
#define CH43 36
#define CH44 37
#define CH45 38
#define CH46 39
#define CH47 40
#define CH48 41
int channels[] = {CH01,CH02,CH03,CH04,CH05 ,CH06,CH07,CH08,CH09,
CH10,CH11,CH12,CH13,CH14,CH15,CH16,CH17,CH18,CH19,CH20,CH21,CH22,
CH23,CH24,CH25,CH26,CH27,CH28,CH29,CH30,CH31,CH32,CH33,CH34,CH35,
CH36,CH37,CH38,CH39,CH40,CH41,CH42,CH43,CH44,CH45,CH46,CH47,CH48};
int incomingByte[CHANNEL_COUNT];
int i = 0; // Loop counter
volatile unsigned long timer_a = 0; // new line
//setup the pins/ inputs & outputs
void setup(){
// enable the watchdog timer with a time of 1 second. If the board freezes, it will reset itself after 1 second.
wdt_enable(WDTO_1S);
// specifically for the UNO
sei();
// initalize PWM Channels / Pins
for (i=0; i < CHANNEL_COUNT; i++){
pinMode(channels, OUTPUT);
}
// set all the realys to off to start with
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
digitalWrite(channels, LOW);
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
digitalWrite(channels, HIGH);
}
}
testSequence();
// set up Serial according to the speed defined above.
Serial.begin(VIXEN_COM_SPEED);
}
void loop()
{
if (Serial.available() >= (CHANNEL_COUNT+2)) {
wdt_reset(); // resets the watchdog
timer_a = millis (); // new line
int uno = Serial.read();
if (uno == 126){
int dos = Serial.read();
if (dos == 33){
for (i=0; i < CHANNEL_COUNT; i++) {
// read each byte
incomingByte = Serial.read();
}
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
int value = incomingByte;
if (value <= 127) {
digitalWrite(channels, LOW);
}
else {
digitalWrite(channels, HIGH);
}
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
int value = incomingByte;
if (value < 127) {
digitalWrite(channels, HIGH);
}
else {
digitalWrite(channels, LOW);
}
}
}
}
}
}
// Random mode code. Random mode starts if no serial input has been received in TIME_OUT millisenconds
else {
wdt_reset(); // resets the watchdog
unsigned long diff = millis() - timer_a;
if (diff >= TIME_OUT) {
timer_a = millis ();
int random_a = 0;
for (i=0; i < CHANNEL_COUNT; i++){
random_a = random(0, 2);
if (random_a == 0) {
digitalWrite(channels, LOW);
}
else {
digitalWrite(channels, HIGH);
}
}
}
}
}
void testSequence(){
if (MODE == NOT_INVERTED) {
for (i=0; i < CHANNEL_COUNT; i++){
wdt_reset(); // resets the watchdog
digitalWrite(channels, HIGH);
delay (500);
digitalWrite(channels, LOW);
}
}
else {
for (i=0; i < CHANNEL_COUNT; i++){
wdt_reset(); // resets the watchdog
digitalWrite(channels, LOW);
delay (500);
digitalWrite(channels, HIGH);
}
}
}
Thank you lightUp! I have posted the sketch and hopefully you can lead me in the right direction!
keyman6868 wrote:Thank you lightUp! I have posted the sketch and hopefully you can lead me in the right direction!
Your sketch does not use a serial breakout board, so don't use one.
Your sketch uses 48 channels so your Vixen sequence must also send 48 channels.
If you want less, then as the instructions indicate you must change the variable "#define CHANNEL_COUNT 48" to something else AND change the Vixen channel count to the same number so that Vixen sends exactly the same channel count as your Arduino will read.
Your sketch also uses a header with these two symbols ~! so include that in the Vixen generic serial setup in the header section. No footer is used.
Your Vixen serial port number must be the same as your Arduino COM port number, as shown in the Device Manager.
Don't open the Serial Monitor in the IDE because it will interfere with Vixen.
So where are you in this process as outlined above?
