Problem whit contro...
 
Notifications
Clear all

Problem whit controlling LED´s

23 Posts
10 Users
0 Reactions
6,240 Views
Posts: 1041
Topic starter
(@christmas-light)
Noble Member
Joined: 18 years ago
[#9248]

Hi

I have 3 Ren 24 v3.3 (frank´s)

I am using led light.

My problem is when dimm one channel then all the channels come on, but there is nothing to see on the status led on the controller.. What can it be :confused:

PS. I have tried to reflash the PIC and tried whit a satnd alone ren 24 and nothing is helping 🙁


22 Replies
Posts: 464
(@holtm)
Honorable Member
Joined: 19 years ago

I had a similar problem with mixed LED and incandescents. If I dimmed the 1/2 wave LED the neighboring channels came on at about 1/2. I added a rectifier between the SSR and the LED string and it went away. I don't know what caused it. Are you using 1/2 wave LEDs?


Reply
Posts: 577
(@photovor)
Honorable Member
Joined: 19 years ago

Have a look here for a possible solution:
http://crazylightlady.us/TerminatorsHow-To.html


Reply
Posts: 1041
Topic starter
(@christmas-light)
Noble Member
Joined: 18 years ago
holtm wrote:I had a similar problem with mixed LED and incandescents. If I dimmed the 1/2 wave LED the neighboring channels came on at about 1/2. I added a rectifier between the SSR and the LED string and it went away. I don't know what caused it. Are you using 1/2 wave LEDs?

Hi

I have tried with a resistor and that did not help

I do not know if I have 1/2 wave LED´s (Ebay light)

Yes I have the same problem as you had... Is it possible that you can take a picture of what you have done ??

Thanks


Reply
Posts: 1763
(@santacarl)
Noble Member
Joined: 19 years ago

You can tell if they are 1/2 wave by picking up the strand and moving it while they are on.....if they appear to shimmer or glimmer.....they are 1/2 wave....I'm guessing that off Ebay you got the 1/2's.....


Reply
Posts: 209
(@marx1)
Reputable Member
Joined: 18 years ago

I had the same problem with my longer strands - it would cause other channels to randomly fire. not dim etc. I did not go with the led's I used a single c9 on the longer channels and all was well


Reply
Posts: 1041
Topic starter
(@christmas-light)
Noble Member
Joined: 18 years ago

I think that they are 1/2 wave LED´s, but what can I do ??


Reply
Posts: 464
(@holtm)
Honorable Member
Joined: 19 years ago

Here are the photos. I wired a bridge rectifier between the SSR and LED.
The first photo shows the wiring. The second shows what is in the rectifier box.

bridge1
bridge2

Reply
Posts: 1041
Topic starter
(@christmas-light)
Noble Member
Joined: 18 years ago
holtm wrote:Here are the photos. I wired a bridge rectifier between the SSR and LED.
The first photo shows the wiring. The second shows what is in the rectifier box.

Hi

I have done the same ting

eg

from my ren 24 -> bridge -> led light

and I have also done this:

From my Bridge -> SSR - > Led light

but it did not help on my ren 24 🙁

I have also tryed:

Bridge -> the half of my ren 24 -> led light

And that worked but when I connected the rest of my ren 24 then the bridge exploded 🙁


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

Your Ren 24 has two sep circuits. Maybe you could run it with two "Bridges". Not sure what the ratings are.


Reply
Page 1 / 3
Share: