Super Strip Flood C...
 
Notifications
Clear all

Super Strip Flood Controller

240 Posts
30 Users
0 Reactions
91.7 K Views
Posts: 1372
(@fathead45)
Noble Member
Joined: 18 years ago

oh that is good to hear. these will run my archs perfect.


Reply
Posts: 859
(@smartalec)
Prominent Member
Joined: 17 years ago
fathead45 wrote:oh that is good to hear. these will run my archs perfect.

Thats ezactly what i was thinking, as well as a led flood or 2.
great work..
how much are the PCB's an when's the next coop?

side comment, i probly would of left the inputs as the rj45's an changed the outputs to be pin headers. (more adaptable then)


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
smartalec wrote:Thats ezactly what i was thinking, as well as a led flood or 2.
great work..
how much are the PCB's an when's the next coop?

side comment, i probly would of left the inputs as the rj45's an changed the outputs to be pin headers. (more adaptable then)

Don't know pricing yet - it will depend on the quantity of boards. Not sure which outputs you're referring to but if the serial interface remember this is for Renard and DMX protocol. I'm still laying out the 2nd revision.


Reply
Posts: 859
(@smartalec)
Prominent Member
Joined: 17 years ago
budude wrote:Don't know pricing yet - it will depend on the quantity of boards. Not sure which outputs you're referring to but if the serial interface remember this is for Renard and DMX protocol. I'm still laying out the 2nd revision.

i was hoping it was for Renard protocol,
i was meeing how you have the rj45's sockets as outputs, could they be pin headers instead

also whats whith the big earth plain on the board around the pic chips? is it for noise or something?


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
smartalec wrote:i was hoping it was for Renard protocol,
i was meeing how you have the rj45's sockets as outputs, could they be pin headers instead

also whats whith the big earth plain on the board around the pic chips? is it for noise or something?

The strips have RJ45 connectors - it's only natural to have a matching connector on the controller side as well. Yes - it's a ground plane - it helps keep noise down.

I think I now have the new layout complete. It won't have a DMX-THRU RJ45 (it would have taken way too much space and rerouting) but I did add a simple 3-pin header if you want to wire up a thru interface with a keystone jack or something. There's no isolation or anything so it's just a basic connection.

Anyway - once I confirm full 48-channel operation and Renard RS-232/485 testing I'll send out for a couple more protos. I didn't get anything done this weekend - you know how life is...


Reply
Posts: 1372
(@fathead45)
Noble Member
Joined: 18 years ago

i got some rgb leds string that could be used to help test them haha. now you got me all excited to try dmx this year. now i just need to get 7 dmx to grinch convertors


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago

I'm happy with the DMX portion of testing - I'll be burning standard Ren/DC code into the PICs next and run through that. I'm pretty sure on the layout at this point so I sent out for a couple more protos which will hopefully be the final version since those setup costs add up quick... Once the final boards are in my hands I'll start an interest thread and then it's a simple matter of reordering. A quick SWAG at price will be $15 or less delivered depending on total quantity.


Reply
Posts: 1372
(@fathead45)
Noble Member
Joined: 18 years ago

that sounds pretty good. i will probably be in for 6 to 10 of them.

did you have an idea on the bom price?


Reply
budude
Posts: 10400
Topic starter
(@budude)
Illustrious Member
Joined: 18 years ago
fathead45 wrote:that sounds pretty good. i will probably be in for 6 to 10 of them.

did you have an idea on the bom price?

I think I mentioned this before but it will be ~$35 in single qty price from Mouser - I'm going to be ordering a set or two of parts to verify those specific parts work over the mix/match of parts I have on the prototype.

6-10 ? I assume you are going to be driving something other than Frank's strips then (unless you're getting 120 strips!)? I'm only spec'ing it to the strip requirements so I'll have to caution you that you might be in unchartered waters. I am recommending 5v (well regulated - no voltage regulator required) or 9-12v with regulator installed. The transistors max out at like 50-70v but of course the regulator won't take that for the PIC power. Even at 24v it will get hot. I have a heatsink in the BOM but it's a fairly simple one.

The other thing will be the total current draw will exceed the DC terminal block at some point. The transistors have a 600mA max but I'm only spec'ing to 360mA max. If run at 500mA, that would be 12A (max) through the block which I think is a 10A part... The final boards will be 2oz copper and it's a pretty wide common run so I'm confident it will work fine. If you're creative/cautious with your sequencing you might be alright.

Anyway - "Officially" I don't recommend going beyond 12v or 360mA/output.


Reply
Posts: 1372
(@fathead45)
Noble Member
Joined: 18 years ago

thats really doable. i can run the rgb leds in a series/parallel to keep it at 12volts. it will just add a few wires. i was hoping it would hold 24v but i can make due. each output will only be running at 120ma so i will only be at 5.75 amp total for the board. thsi would be for my rgb archs. my mega tree will be leds running on 110 so im not worried about that.


Reply
Page 8 / 24
Share: