Renard-WC Wireless ...
 
Notifications
Clear all

Renard-WC Wireless Controller

266 Posts
47 Users
0 Reactions
119.3 K Views
Posts: 999
(@ppohlman)
Noble Member
Joined: 19 years ago
IdunBenhad wrote:Hi:
I found that the Rev 6 XBee board will not work directly with a 16 channel XMUS board.

The SMA wireless board works fine as a receiver, but the Rev 6 does not. The modification of the Rev 6 is simple and takes less than 5 minutes.

If anyone is interested in the modification, let me know and I will detail it. It takes longer to list it than it does to do it.

Merry Christmas

I would be interested. I have a Ren16 XMUS board and tried to use the Ren-W with it to no avail. I'd like to know how to make it work for next year.

Thanks.


Reply
IdunBenhad
Posts: 1603
(@idunbenhad)
Noble Member
Joined: 18 years ago

Hi:
The modification is really simple.

First, some explanation. On the REV 6 board, the DATA OUT of the XBee goes through two inversions through the MAX232 chip. Only 1 inversion is needed, so that's what we are going to do. Also, one side of the data signal needs to be grounded.

1..Remove the RX jumper.
2..Put the jumper on JP1...This grounds Pin 5 of the RS485 cable.
3..Solder a small wire jumper from Pin 11 of the MAX232 to the Pin on the TX jumper that connects to Pin 4 of J1, the RS485 connector. There should be no jumper on the TX or RX pins.

That's it. The signal is picked up between the two inverters and fed to Pin 4 of the RS-485 connector/cable.


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago

Why does the XMUS require this mod to the Ren-W but other boards don't? Does the XMUS have different communication hardware or something?


Reply
IdunBenhad
Posts: 1603
(@idunbenhad)
Noble Member
Joined: 18 years ago

Hi:
No, the XMUS is the same as the other boards, but dirknerkle designed the wireless boards primarily for the SS series.

If you look at the schematic for both type boards, you will see that the DATA IN circuitry is almost identical. There is provision to use RS232 on the SS series, but not on the XMUS.

On the REV 6 board, the RX DATA is inverted twice. This is to make it RS232 equivalent. On the SMA boards, the RX data is inverted once through the MAX232 chip.

All I did was make a connection between the two inverters on the MAX232 so the data was the same as the SMA board.

I know dirknerkle has a better explanation than I, so he will probably be joining in here sometime. He is considering making this a permanent modification to the REV 6, but because there is a very limited number of people using the XMUS board with the wireless boards, it's probably not worth the expense and effort. The mod. takes about 5 minutes and is very simple, as you can see from the above post.

The only reason I was using the REV 6 board instead of the SMA is because it was there! And, I had already drilled mounting holes for it before I discovered it wouldn't work.


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

The main reason the Rev6 board uses both pins 4 and 5 is because it has only one RJ45 jack while the SMA board has two. As a practical matter, to make the RJ45 work both for transmitting and receiving, I decided to keep the pins unique, so I fed the MAX232 back to itself and reinverted it so all you had to do was jumper either the RX or TX headers.

Idun's solution is a good one and is simple. I have an Xmus board myself that I have not yet tested (I think it's about the only Renard I hadn't seen before I put the Rev6 out) and adding another pair of header pins wouldn't be very hard. But he's also right -- the overall number of Xmus boards out there for those who are interested in wireless might be quite small. The mod obviously works (just a small 1/2" wire across two solder points) but I'll have to check how compatible the board is with other Renards AFTER the mod. My original goal was to create a "plug-in" solution, and the SMA board accomplishes that. The Rev6 was kind of a hybrid because of the single RJ45 jack for both receiving and transmitting.


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago

Oh, I see.


Reply
IdunBenhad
Posts: 1603
(@idunbenhad)
Noble Member
Joined: 18 years ago

Hi:
That Jrd is a man of few words!


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago

Yes.


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago

And that budude is a man of few word.


Reply
Posts: 3277
 Jrd
(@jrd)
Famed Member
Joined: 19 years ago

Sunday morning I was testing my display (which had lost power overnight due to a GFCI tripping) and it seemed to lag behind until it tripped again. (GRRR!)

Are the XBees less stable when cold?

I am considering adding a night light bulb to my controller box for warmth when the triacs aren't going.


Reply
Page 21 / 27
Share: