Yes, the series 2 modules are the "digi-mesh" system, which is point-to-point and an entirely different structure to the network.
I goofed on an order once this last summer and received 6 of them. I opened one package, tried them out, couldn't change them, read a lot of doco on them, called Mouser for an RMA and they took them back no questions asked when I told them I accidentally ordered the wrong part. So all it cost me was shipping two ways, which isn't much when you consider they don't weigh very much!
I've also done some research on the Microchip wireless modules, and they're pretty interesting. Some are limited to about 300' transmission distance while others are up to 400m. Higher throughput, possibly, but it also appears that you have to write some code to use them with the pics. I'm not sure how much overhead they'd be to the 16F688's for that extra processing -- I doubt it would fly because Phil's timing is so tight. It sure doesn't look as simple as using XBees, but then again, I haven't tried it... I will leave that project to someone else as my R&D budget was tapped out many times over in working on Ren-W.
I started putting a Ren-W together and got to the step to add the jumper headers but they don't seem to fit, even with wiggling or using pliers. They are the same number as in the BOM, or atleast that is what I ordered and what the bag says but they are white not black like in the pics.
I am using a rev 20100219 board.
Did Mouser send me the wrong part or were the holes too small on this version of the board?
Thanks
On some of the boards, the holes are a bit small because of the through-hole solder. Just drill them out just a bit, or take a knife and scrape the corners of the jumper header so it will fit. That was an unfortunate manufacturing inconsistency...
My board only has a pad on the bottom so it isn't being closed up by the through-hole solder.
I don't think I have a drill bit small enough to not destroy the pad so I will try the knife method, thanks!
Jrd wrote:My board only has a pad on the bottom so it isn't being closed up by the through-hole solder.
I don't think I have a drill bit small enough to not destroy the pad so I will try the knife method, thanks!
You have the light green translucent boards? Wow... those are rare... I had only a dozen of those made -- it was a test of a new board provider. They worked fine but yes, they didn't drill some of the holes the right size. Shaving down the corners of the pins should work -- I did that on a couple of them instead of drilling them out.
I don't know if you have a Dremel moto tool, but it's one of the handiest tools you can have for electronics work. You can get really tiny drills, saws, grinders, and all sorts of things that make it easy to modify a case for things, mod a board, cut a board tracing, or with their small diamond wheel, cut through just about anything. It's an amazing little tool -- I use it all the time. But because I often etch my own boards, I've found it particularly handy for drilling component holes. Tiny drill bits are cheap and if I de-solder a part and end up with a solder-filled hole, it's a lot safer and quicker just to drill a new hole through the solder than try to suck it out and possibly lift a trace.
dirknerkle wrote:You have the light green translucent boards? Wow... those are rare... I had only a dozen of those made -- it was a test of a new board provider. They worked fine but yes, they didn't drill some of the holes the right size. Shaving down the corners of the pins should work -- I did that on a couple of them instead of drilling them out.
Yea that's them, you sent them to me a while ago.
I don't know if you have a Dremel moto tool, but it's one of the handiest tools you can have for electronics work. You can get really tiny drills, saws, grinders, and all sorts of things that make it easy to modify a case for things, mod a board, cut a board tracing, or with their small diamond wheel, cut through just about anything. It's an amazing little tool -- I use it all the time. But because I often etch my own boards, I've found it particularly handy for drilling component holes. Tiny drill bits are cheap and if I de-solder a part and end up with a solder-filled hole, it's a lot safer and quicker just to drill a new hole through the solder than try to suck it out and possibly lift a trace.
Yea I do, actually there might be two floating around.
Thanks, I'll see if the one I have has a drill bit of the right size.
Hi:
There is an alternative to a Dremel tool for small size bits.
Auto parts stores like O'Reilly and Auto Zone may have a small set of bits for drilling out jets for carbs (I know, it dates me). Also, these might be available from a plumbing supply store for drilling out jets in water heaters, etc., or maybe a motorcycle repair shop.
I have a set that is actually a small hand drill. The bits store in the handle and the chuck is built-in on the end.
IdunBenhad wrote:Hi:
There is an alternative to a Dremel tool for small size bits.Auto parts stores like O'Reilly and Auto Zone may have a small set of bits for drilling out jets for carbs (I know, it dates me). Also, these might be available from a plumbing supply store for drilling out jets in water heaters, etc., or maybe a motorcycle repair shop.
I have a set that is actually a small hand drill. The bits store in the handle and the chuck is built-in on the end.
You can also buy these at welding supply stores. They are used to clean out the tips on torches.
IdunBenhad wrote:Hi:
There is an alternative to a Dremel tool for small size bits.Auto parts stores like O'Reilly and Auto Zone may have a small set of bits for drilling out jets for carbs (I know, it dates me). Also, these might be available from a plumbing supply store for drilling out jets in water heaters, etc., or maybe a motorcycle repair shop.
I have a set that is actually a small hand drill. The bits store in the handle and the chuck is built-in on the end.
Thanks for the idea, I just used the dremel with a 3/64th" bit, the 1/32 was just big enough to scrape the sides but didn't make the hole big enough for the jumper.
The board is now finished.
Hi:
I found that the Rev 6 XBee board will not work directly with a 16 channel XMUS board.
The SMA wireless board works fine as a receiver, but the Rev 6 does not. The modification of the Rev 6 is simple and takes less than 5 minutes.
If anyone is interested in the modification, let me know and I will detail it. It takes longer to list it than it does to do it.
Merry Christmas


