Jrd wrote:Your welcome 🙂 I've heard that grape juice helps with memory, unfermented grape juice that is.
Yah, and that's both good and bad for us old guys...
...it's good that it helps with memory so you can remember that you have to pee afterward! 😆
(To all you young'uns out there who are laughing right now... you'll find out later on exactly what I'm talkin' about, 'cuz your day is comin'! 😛 )
dirknerkle wrote:(To all you young'uns out there who are laughing right now... you'll find out later on exactly what I'm talkin' about, 'cuz your day is comin'! 😛 )
And it's our goal in life to hang around long enough to say "I told you so".
Hi:
Yeah, but the neat thing about getting old is you can hide your own Easter eggs and tell jokes that are very old but the younger ones haven't heard them. Makes you look like a stand-up comedian.
I also put on the back of my credit card: "See Photo ID". Makes them look at my drivers license and at the same time, I can tell them my own name.
Oh, I forgot to go look at the WiKI! On the way now.
Hey folks, I've been doing some experimenting and I've found that using Vixen and the Ren-W at 57600, Mark parity and 1 stop bit seems to work better for me than with 2 stop bits. Not sure why exactly, but my anectodotal evidence is that my display seems more responsive and timing is more exact.
So my suggestion is to continue to use the 57600 baud and set the XBee and your Vixen plug-in to MARK parity, but as XBee doesn't have a stop bits setting, do your own experimentation with your Vixen plugin configuration. Try two stop bits, and then try one stop bit and see if there's a difference for you. There has been a noticeable difference for me, but everybody's case is unique because of the orientation of the antennas, where the controllers are located, where your transmitter is, etc. In my case, my transmitter is indoors inside the garage and the signal has to go through three walls, each of which has aluminum siding to get to some of my controllers.
dirknerkle wrote:Hey folks, I've been doing some experimenting and I've found that using Vixen and the Ren-W at 57600, Mark parity and 1 stop bit seems to work better for me than with 2 stop bits. Not sure why exactly, but my anectodotal evidence is that my display seems more responsive and timing is more exact.So my suggestion is to continue to use the 57600 baud and set the XBee and your Vixen plug-in to MARK parity, but as XBee doesn't have a stop bits setting, do your own experimentation with your Vixen plugin configuration. Try two stop bits, and then try one stop bit and see if there's a difference for you. There has been a noticeable difference for me, but everybody's case is unique because of the orientation of the antennas, where the controllers are located, where your transmitter is, etc. In my case, my transmitter is indoors inside the garage and the signal has to go through three walls, each of which has aluminum siding to get to some of my controllers.
Thats exactly what I found, ie. 57600 mark and stop 1. I am using the explorer/programmer board from a USB port as my transmitter, thus keeping it away from other serial / Vixen plugins, not as if that should make any difference. Running a 24ss and 16ss approx 200 feet away with no hicup. Great unit and continuing info Sir.
Dave
We tried our first test run last night with the houses at both ends of the block. I did see just a few minor miss fires. I changed the angle of the receive antenna and that seem to help. But I am still running two stop bits. I will try one stop bit on our next try. It seems to be working really well so far. We have 8 of the 14 houses wired and ready, but the rain is stopping us from testing anymore today.
So if I understand this correctly, the only place I will need to change the stop bits is in the plug-in for vixen, correct?
I will give it a shot on my simulator first and see what it does.
Thanks for the info.
Hi, Ted. Yes, that's the only change -- just in the Vixen plugin setup on the PC. What I have not yet checked was whether it affected channels 57-64 yet, but I plan to check that today.
I'm checking it now. and will let you know in a few min if it works.
Ok, I tried it on the simulator, and for me it is a no go. It may be that the transmit and receive antennas are to close, (within 10 feet of each other).
I will have to try it once we get to more testing outside. The long USB cable may give me a long enough delay to satisfy the timing.
I just checked if from my garage transmitter down to my workshop -- the one stop bit setting seems to work just fine on all channels for me.
dirknerkle wrote:Mark parity and 1 stop bit seems to work better for me than with 2 stop bits.
Dirk, it's the Placebo effect. Mark and 1 stop bit is identical to no parity and 2 stop bits.
