jcarney wrote:I am having some missed transmissions and I am trying to figure out which end it is on, the recieve or transmit side. I tried the troubleshooting steps but when I open the terminal window and try to view the hex vixen says "Access to Port 'COM5' is denied" (COM5 is my explorer board). If I run vixen first X-CTU says basically the same thing.Wrong driver installed? It did take a few different driver tries to get it (USB Explorer Board) to communicate with X-CTU.
EDIT: I reinstalled the driver and it now shows the same title as the wiki page but I still get the same results from trying to watch the hex values.
XCTU expects the explorer board to be put in the same USB slot every time. Also, if Vixen is running and also accessing the same port at the same time, it creates a "sharing" conflict. If Vixen isn't running, check the Windows taskbar anyway -- I've seen a hidden copy of Vixen in the processes window before.
Another problem is if the transmitter is too close to the receiver. It can overdrive the receiver if they're only a foot or two apart -- thanks to tweist on that one. IGWS that the communication protocol on both the tx and rx sides must be identical...
I think I was following the troubleshooting tips wrong. Here are some other reasons I think this might be happening. I have a receive only board, and the test points don’t make sense. When connecting to the ground and 5v point I get .057v when I connect to the 5v and the ground on the Renard it measures 5v. The 3v point with the Ren-W ground measures 0 and the 3v point and the ground from the Renard measures 4.88. Also the power LED doesn’t light but I thought it was because I but it in backwards but I reconfirmed and it is oriented the right way. My guess is I don’t have a solid ground but I don’t know how to troubleshoot that. Thanks for your patients and help.
jcarney wrote:I think I was following the troubleshooting tips wrong. Here are some other reasons I think this might be happening. I have a receive only board, and the test points don’t make sense. When connecting to the ground and 5v point I get .057v when I connect to the 5v and the ground on the Renard it measures 5v. The 3v point with the Ren-W ground measures 0 and the 3v point and the ground from the Renard measures 4.88. Also the power LED doesn’t light but I thought it was because I but it in backwards but I reconfirmed and it is oriented the right way. My guess is I don’t have a solid ground but I don’t know how to troubleshoot that. Thanks for your patients and help.
Is your Ren-W connected to your Renard via a straight through along with the power?
Jrd wrote:Is your Ren-W connected to your Renard via a straight through along with the power?
I am not sure what you mean by a straight through?
I am a little brain dead and didn't even think about how it was grounded. My measurements were taken without the CAT5 being connected to the Renard. I connected the Renard to the Ren-W and all the point are correct. I am still working through trying to get a more accurate connection between the two (USB explorer board and the receive only board). I did order a better antenna for the SMA XBee Pro so I will see if that has an impact.
jcarney wrote:I think I was following the troubleshooting tips wrong. Here are some other reasons I think this might be happening. I have a receive only board, and the test points don’t make sense. When connecting to the ground and 5v point I get .057v when I connect to the 5v and the ground on the Renard it measures 5v. The 3v point with the Ren-W ground measures 0 and the 3v point and the ground from the Renard measures 4.88. Also the power LED doesn’t light but I thought it was because I but it in backwards but I reconfirmed and it is oriented the right way. My guess is I don’t have a solid ground but I don’t know how to troubleshoot that. Thanks for your patients and help.
If this is a Rev6 board, the LED on the board will blink when the XBee radio is plugged in and operating. It's a status indicator that the XBee is working properly. If it's an SMA board, the LED will be on regardless of whether the XBee is plugged in or not.
On the SMA, pins 1 and 2 are ground, which is the same as JP4. With an SMA in receive only mode, there should be NO JUMPERS on the board whatsoever, the XBee radio should be in the RX side (right) side of the board, a normal straight-thru cat5 cable (same as any cable you'd use to connect a computer to a network switch) should be connected from J2 (the right RJ45 jack) on the SMA to the RS-INPUT jack on the controller. You will also need +5vdc power tapped from someplace on the controller board and then connected to either of the two header pins on the SMA board marked JP3. That's it.
On a Rev6 board, the only jumper on the board shold be set on the RX (right) side (no other jumpers), the same cat5 cable connects from the Rev6 to the RS-INPUT jack on the controller. Again, RJ45 pins 1 & 2 are ground, same a JP4. Then you need to tap +5v from the controller board somewhere and connect that to either pin at the Rev6's JP3. That's it.
At the +5v test point, you should get something very close to +5v (possibly 4.96, or something like that. It should be exactly the same voltage measurement as where you'd check for +5v on the controller board.
At the +3v test point, you should get something very close to 3.3vdc. With the proper parts, it should lock in at exactly 3.3v.
jcarney wrote:I am not sure what you mean by a straight through?I am a little brain dead and didn't even think about how it was grounded. My measurements were taken without the CAT5 being connected to the Renard. I connected the Renard to the Ren-W and all the point are correct. I am still working through trying to get a more accurate connection between the two (USB explorer board and the receive only board). I did order a better antenna for the SMA XBee Pro so I will see if that has an impact.
Sorry I meant a straight through cable. Like Dave said it is the same thing as you would use to connect a computer to a hub or switch.
You have to have the Cat-5 cable connected to the controller because that is how the ground connection is made. So, no Cat-5, no ground. That is probably why you got the wrong measurements.
I updated the Ren-W's Wiki with information about XBee antennas. There isn't any plot, intrigue, murder or sex, but some of you might find it helpful reading, anyway....:rolleyes: The new page is called "Ren-W Antenna Info" and is found as the last page of the Ren-W information.
Thanks. I can't even remember my own titles!!! Geez.... gettin' old is a drag...
Your welcome 🙂 I've heard that grape juice helps with memory, unfermented grape juice that is.
