Renard Servo PCB Re...
 
Notifications
Clear all

Renard Servo PCB Redraw

18 Posts
6 Users
0 Reactions
9,207 Views
Posts: 44
Topic starter
(@lefty12)
Trusted Member
Joined: 16 years ago
ctmal wrote:In the BOM, c1 should be gone and C4 should be the value that is in C1.

I will get everything updated and reposted later today! 🙂

thanks to all who have helped!
Randy


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

Place the reference designator in a convenient location outside of the part. This makes it easier to locate a part when trouble shooting.

Also I find it easier to build boards if the part value is placed underneath the part. Once you place a part on the board, you have the value on the part itself. It’s not necessary for the obvious parts like connectors, etc.


Reply
Posts: 44
Topic starter
(@lefty12)
Trusted Member
Joined: 16 years ago

I have updated pcb, sch, and bom as of 6/13/2011 am.

I did add the power connection for the servos as many now will accept 6 v plus!
moved the designators, the + and - sign, tried to adjust the power 4 point cross, the trace from J2p3 running too close to J2p1
adjusted some componet locations (slightly), pulled what hair I have left out! 🙂

the updated files are in post #1

Randy


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago

A yellow silkscreen is kind of hard to see but through the magic of graphic editors I was able to view it anyway.

I don’t want to sound nitpicky but I’m assuming it’s what you want.

Reference designators R1 & J1 are still inside the part. ‘5 v dc’ is under the connector. R3, R2, C1 & D3 designators are partially covered by the part silkscreen but its fine if that’s what you want. I usually set the grid to 5 mils when placing reference designators. It gives you a little more movement be still allows you to a line things.

J4 is too close to the pads and most of it will be removed based on the solder mask layer.


Reply
Posts: 44
Topic starter
(@lefty12)
Trusted Member
Joined: 16 years ago

I have updated the pcb file, changed silkscreening to white, top layer to blue. (simply a preference on my part) The reason the original slikscreen was yellow was because express pcb had that set as the default after download. (doesnt make sense as when you order the info on the screen says the silkscreen will be white.) I will agree with you Ernie, I had trouble with the yellow too especailly with the red underneath it! I didnt even think to look for an options setting to change the colors. I think I got the J4 far enough away now.
Randy


Reply
ErnieHorning
Posts: 4434
(@erniehorning)
Famed Member
Joined: 19 years ago
lefty12 wrote:I think I got the J4 far enough away now.

In my previous post, I was only speaking of the silkscreen. The copper all looks good.


Reply
Posts: 44
Topic starter
(@lefty12)
Trusted Member
Joined: 16 years ago

I recieved the pcb's from Express PCB last Friday. I assembled one of the boards Saturday and tested it Sunday! Had a few problems as I tried to use the skull Output to drive the servos by assigning the channel/(servo) numbers to it. Couldnt get any movement although as soon as the servo was plugged in it centered itself. I PM'd Chris and found out that the Skull Output plugin is only a visual aid to actually see the skull moving while the sequence is being played. The servos are actually driven by the Renard Dimmer (modified) output pluggin. I assigned the servo channels to the Renard Dimmer, hooked up the cables, powered it up and I had servos jumping all over the place with the sequence! I attached Skulley, (so named by my lovely wife,,,,,) adjusted the servo arms to be centered. turned on the sequence and everything worked great! At nutral everything is steady as can be, no glitching or hunting for center!

I have uploade the most current files associated with the PCB. It is located in the first post.

I need to say a BIG thanks here to Chris, he has been extreemly helpful!
Thanks Man!

Randy


Reply
Posts: 67
(@jamesl85)
Trusted Member
Joined: 16 years ago

Videos!!! We want videos!!!!

James


Reply
Page 2 / 2
Share: