NRF24L01 - eagle la...
 
Notifications
Clear all

NRF24L01 - eagle layout?

60 Posts
11 Users
0 Reactions
36.7 K Views
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

I'm still debugging the Receiver units. The Transmitter is working now (currently only sending a single 32 channel block, but this proves out the hardware side).

Fixes that were required:
a. The incoming OPTO for the SN75179B output was inverted. That is to say I should have had the line pulled high, and used the input from the 75179 to pull the signal low. Versus having the 75179 trying to push the signal high. (Hope that made sense)
b. DSI/DSO pin swap. (Why oh why oh why.. don't they label these as MISO/MOSI ?? (sigh)).

Hope to have pictures over the weekend, but kids have another "show on the go".


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

After *WAY TOO MUCH* head banging, I finally got the NRF receiver code on the 16F1825 operational. I got caught by the pesky turn off analog input snafu for the pins on portC (ANSELC). Yep.. every 10 years or so I get caught by that once again.

Here's the pictures, though I have to say I've done much better with photo's in the past. Might be because I'm trying to film in the evening, rather than during the day.

The transmitter ... using an external antenna NRF module. Range had me wandering 2 doors down the street, with the device transmitting from the floor of my living room.
Fully isolated DMX input and output.

DMX2NRF1
DMX2NRF2

And the Receiver... (3 chan capable of driving a full 5M RGB (30 led/m) strip, without even feeling warm)

NRF RX1
NRF RX2

To do... build up a few more, and get the NRF2DMX code operational. The intent is that NRF2DMX module would detect the lack of a DMX signal, and change into Receive mode. At which point it will start listening for NRF packets and GENERATING a DMX signal.


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago

Good work, Labrat.

How long is your antenna? 6-1/2"?

I bought an antenna that has 9dBi of gain and is 14" long but don't know how much additional range one would get. It also claims to be omni-directional.


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Antenna was purchased years ago for use with a microchip development platform. I bought two at the time, and this one has sat idle until now. I will have to measure to see how big it is. As I recall it was intended to replace a foil based antenna that came with a demo board.


Reply
LabRat
Posts: 2981
Topic starter
(@labrat)
Famed Member
Joined: 17 years ago

Posting this story for the benefit of others... (sigh)

Did anyone else hear the sound of my head pounding against my desk last night? I soldered up a second Transceiver board (to be used to develop the NRF2DMX side of the equation), but the PICKIT3 was unable to identify the device (PK3ERR0035). I spent the whole evening carefully inspecting every solder joint, re-soldering numerous connections (just in case), before eventually giving up around 1:30 am.

This morning I had a few minutes before heading off to the Orifice, and tried again... *but* this time I dropped the voltage on the PK3 from 5.0v (the desired voltage for the PIC) to 3.3v. "Presto.. device identified and can be programmed".


Reply
Page 10 / 12
Share: