MiniRen8/4
 
Notifications
Clear all

MiniRen8/4

130 Posts
29 Users
0 Reactions
50.4 K Views
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago
griffixdc wrote:what is this ? and how much? pm me if you want i am not available as much as i used to be replying through PM would probably be better:)

WiRen was an experiment that never got past a prototype set I made. I put the circuit board tracings and a brief manual in the copper section of the file library. It's free -- you make your own boards as there are no commercial WiRen boards on the planet.

MiniRen8/4XB is also in the copper section of the file library and you can make your own board for it, too. There's a 10-page manual there that you should read if you're interested in it. I have a short run of commercial boards on order for those who don't want to try to etch their own.

Just as a heads-up, you'll find that a comment or posting in any particular thread is almost always related to one or more prior postings within the same thread, and you often will have to read backwards into the thread to understand what it's all about. The WiRen is a perfect example, and it was also covered earlier in this thread. I suspect that it's probably not your style to read backwards into a thread to get the background, but that's how open forums work.


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

A couple users have asked about replacing the on-board SSRs on the MiniRen8/4XB with two RJ45 jacks. Piece of cake. You can either do it youselves or go to the file library and get the PCB layout for it there. I've added it as: MiniRen8XB w/o SSRs.

This should cover most of the bases at this point for all the users who want to build either a wireless SSR or a small wireless Renard. And just taking a quick stock of what's available now in the Renard line, users have lots of wireless options:

** Ren64 with Ren-W for 64 channels and external SSRs
** Olsen595/Ren-C with Ren-W for 64 channels and external SSRs
** Grinch/Ren-C with Ren-W for 64 channels and external SSRs
** Ren48LSD with Ren-W for 48 channels and LEDs and/or external SSRs
** Ren24 with Ren-W for 24 channels and on-board SSRs
** Renard SS24 with Ren-W for 24 channels with on-board SSRs
** Ren24LV with Ren-W for 24 channels and LEDs and/or external SSRs
** Renard Simple 24 with Ren-W for 24 channels and external SSRs
** Renard SS16 with Ren-W for 16 channels with on-board SSRs
** Renard Simple 16 with Ren-W for 16 channels and external SSRs
** Renard SS8 with Ren-W for 8 channels with on-board SSRs
** MiniRen8XB for 8 channels and external SSRs
** MiniRen8/4XB for 8 configurable channels with four on-board SSRs


Reply
Posts: 448
(@bobkeyes)
Honorable Member
Joined: 17 years ago

That's an impressive line up. Thanks Dirk.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

That's why I use the Hybrid mode. The thread is displayed in the order it was written. So the first time I open a thread I can read it start to current. Then every time after that in the top window it shows the posts I've read and those I have not. And you can click where you want to go in the thread.


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

WiRen Update

Some of you took an interest in some prototyping I did during the development of the MiniRen8/4XB. It was a modular board concept walled WiRen. I decided to forge ahead with it and finish up what was planned by not completed. Here, then, is a completed LSD card and a Relay card. The Relay card has two relays but each has two 120VAC circuits; jumper shunts allow assigning each circuit to be normally open or normally closed status, and you can assign which of the WiRen's 8 channels each relay responds to. Since these are mechanical relays and not dimmable SSRs, you must assign the Vixen control channels to either full on or full off.

I've also included a photo of the completed system -- the main WiRen module and its six interconnect boards.

FWIW, here's a link to the original page that included a couple photos, too...

http://doityourselfchristmas.com/forums/showthread.php?14780-MiniRen8-4&p=147937#post147937


Reply
griffixdc
Posts: 2512
(@griffixdc)
Famed Member
Joined: 16 years ago

without much understanding to what is used to create the dimming effect on the renss series what would be needed to allow your mini's to dim or is that a small space killer?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
griffixdc wrote:without much understanding to what is used to create the dimming effect on the renss series what would be needed to allow your mini's to dim or is that a small space killer?

All of these sub-boards that Dirk created can dim except for the Relay board which is only on/off. The wireless module contains all of the required bits to allow dimming.


Reply
griffixdc
Posts: 2512
(@griffixdc)
Famed Member
Joined: 16 years ago
budude wrote:All of these sub-boards that Dirk created can dim except for the Relay board which is only on/off. The wireless module contains all of the required bits to allow dimming.

so basically these are like the ren64 ..am i following this right?


Reply
budude
Posts: 10400
(@budude)
Illustrious Member
Joined: 18 years ago
griffixdc wrote:so basically these are like the ren64 ..am i following this right?

When you say "these" - what exactly are you referring to? Basically all controllers have a control/logic section (PIC, oscillator, etc) and an output section. What Dirk has done is to modularise these into separate bits. You start with a control board (which is useless on it's own) and then you connect that to one of the various output boards. You end up with a custom made controller for whatever purpose you need - AC, low-current DC, medium-current DC, high-current DC, or just right off the PICs.


Reply
dirknerkle
Posts: 10310
Topic starter
(@dirknerkle)
Illustrious Member
Joined: 18 years ago

Thanks, budude. That's a good way to explain it. The boards are small and all the same size and any two of them would fit into a single outlet box. I've used the WiRen project as a sort of experimentation/learning tool that I thought it would be a cool way to go, but like so many of the experimental things we sometimes create, it took a different turn when I realized that the only thing missing was a 120vac transformer and that would give me what I was originally after: a wireless SSR.

However, I've since found a good use for the WiRen boards I made, and I've mounted all seven of them onto a single pine board along with a wall wart. It's now kind of a universal Renard experimentation platform that is currently just sitting there on a shelf, but one which will come in handy as I start dinging around with redoing light strings, displays, changing-out mini-lights with LEDs, etc. And being wireless, I'm not limited to working in the shop; I can haul it up into the garage, living room, a guest room (or anywhere Mrs. Dirk lets me go in the house...) and do my experimentation with actual display elements regardless of what kind they are or where they are in my house. It's like having a Ren64, one of Wayne's SS boards, one of Frank's Ren24s, a Ren48LSD or even a Kit74 relay board all in one nice, small, portable kit. I can have the sequence running a test loop in my workshop and extend my mess well beyond the confines of my workshop! 🙂 (Shhhhh.... don't tell Mrs. Dirk... she'll find out soon enough...)


Reply
Page 9 / 13
Share: