Inline SSR
 
Notifications
Clear all

Inline SSR

49 Posts
16 Users
0 Reactions
16.5 K Views
JasonPortwood
Posts: 753
Topic starter
(@jasonportwood)
Noble Member
Joined: 17 years ago
n1ist wrote:A few tips:

- Make the AC wiring thick enough to handle your expected current, with suitable margin.
- DO NOT run any traces under the opto, and keep all AC traces at least a quarter inch away from the low voltage side. Otherwise, the traces may be close enough to arc over
- The holes for the wires must be large enough for the wire to fit through, and have enough of a solder pad to secure the wire. If you have space, add an extra hole or two next to the wire terminal so you can strain-relieve the connection by looping the wire thru the extra hole before soldering it
- Optos have 6 pins, even if you are only using 5.
- Avoid having traces that connect to other traces or pads at acute angles; the sharper the angle, the more chance of getting an acid trap. Likewise, it is better to bend traces with two 45 degree bends rather than one square corner
- Think about the form factor; square boards are good to mount in a box (don't forget mounting holes) while longer skinny ones are good candidates to be heatshrunk as a lump on a cable

/mike

Thanks for the tips. What is a suitable width for a trace for 120v operation? Even though it's for me I read on some of the Renard wiki pages they are OK with 240. What's the trace width for that? I'd rather build something universal in case someone else comes along wanting it.

I had planned on just cutting the pin off on the opto but that's probably just a waste of time since I could just have a hole for it.

I'll work on a new version with those tips in mind. The extra holes for stress relief is a great idea. Would it actually work to send the power in from one side and out the other instead of all on the same side?

I'm also going over kychristmas's design as well trying to learn as much as I can.

Thanks!

-
Jason


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

Trace width (and copper weight) determine how much current you can safely handle. According to ExpressPCB, for 1 oz copper, use 0.025" for 1A, 0.05" for 2A.

Trace spacing determine how much voltage you can have between them without arcing.
/mike


Reply
LabRat
Posts: 2981
(@labrat)
Famed Member
Joined: 17 years ago

There are plenty of "online/web based calculators" for determining trace widths.

I like the following site, as it made it easy to jump back and forth between 1oz and 2oz copper thickness.

http://www.desmith.net/NMdS/Electronics/TraceWidth.html


Reply
g2ktcf
Posts: 3651
(@g2ktcf)
Famed Member
Joined: 18 years ago
aixelsyd wrote:I never thought that I would be posting in this forum anytime but here I am. I'd like to build Don's inline SSR which he wrote about here ChaseCicles but to control small segments of retro C9 LEDs (8 - 11 max). I posted about it originally here.
I've emailed back and forth with Don and he said it would be best to get the experts in on this for more input so here I am. My goal is create a PCB for this and get them made. I'll need 27 of them (at first) but I figure with the size of these, 1/2" x 3/4", I could probably fit a bunch on one board and then just cut them apart. It may be cheaper in the long run though to do what Don did and use strip board. Any advice on the best route is most welcomed. My end goal is to make an SSR extension cord. Each tap will be it's own channel.

I have never done any design work before like this, which I'm sure will be evident when you look at the diagram I made. Using Don's original design I drew up a PCB layout. I wanted to post it for people to look over and find out if I'm on the right track. I'll work on making it smaller later. I'm definitely not sure if I did the connection from the middle connection of the triac to the out & the resistor. That looks weird but from Don's picture I figured that's how it would look with traces.

Also does anyone know if this was done before? I figure no reason to reinvent the wheel if someone already made a PCB design. Don did say he thinks someone did do this board before but I couldn't find it in the forums. I did find it talked about a little here and there but nothing solid of someone else repeating it.

Thanks for any advice.

Jason

Jason,

Nice start for the PCB...but I have a question.

The problem for us is the cost of the power wire...the communication cables are cheaper. It normally serves us better to put the SSR at the point of use instead of at the point of source. Does this make sense? It very well could be that you have a special circumstance but I just wanted to point out the challenges cost wise.

Good Luck!
Chris


Reply
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

That's why the inline works. Less Power cable. My 4 channel chasecicle sections have one Ethernet cable and one spt2 wire. The way I did it (only built one) I soldered the 50 ct section of Icicle lights directly to the Inline SSR. My PCB design has it so the board is actually the Union for the spt2 wire. It has in and out for the power cable. As well as an in and out for the common +5v from the data. The only down side is that the Signal/data wires are exposed after the first Single SSR. My four-channel set is wire-tied to a piece of 3/4 PVC Conduit. It looks ugly but works great. Last Year I had i running over multiple days in my shop.

The original thought was to put all of the cable and SSRs inside the conduit. Then there would be an Rj45 Jack and Power Plug on one end. Not sure that would work out and maybe not even worth the effort to avoid the extra cable. For instance, I figured out that my neighbors house would be at least 400 ft of SPT2 if I went the traditional way. Less if I used a 4-Channel SSR mounted on each 4-channel section. Of course those options would not look too good.

g2ktcf wrote:Jason,

Nice start for the PCB...but I have a question.

The problem for us is the cost of the power wire...the communication cables are cheaper. It normally serves us better to put the SSR at the point of use instead of at the point of source. Does this make sense? It very well could be that you have a special circumstance but I just wanted to point out the challenges cost wise.

Good Luck!
Chris


Reply
Page 2 / 10
Share: