Inline SSR
 
Notifications
Clear all

Inline SSR

49 Posts
16 Users
0 Reactions
16.5 K Views
JasonPortwood
Posts: 753
Topic starter
(@jasonportwood)
Noble Member
Joined: 17 years ago
[#18377]

I never thought that I would be posting in this forum anytime but here I am. I'd like to build Don's inline SSR which he wrote about here ChaseCicles but to control small segments of retro C9 LEDs (8 - 11 max). I posted about it originally here.
I've emailed back and forth with Don and he said it would be best to get the experts in on this for more input so here I am. My goal is create a PCB for this and get them made. I'll need 27 of them (at first) but I figure with the size of these, 1/2" x 3/4", I could probably fit a bunch on one board and then just cut them apart. It may be cheaper in the long run though to do what Don did and use strip board. Any advice on the best route is most welcomed. My end goal is to make an SSR extension cord. Each tap will be it's own channel.

I have never done any design work before like this, which I'm sure will be evident when you look at the diagram I made. Using Don's original design I drew up a PCB layout. I wanted to post it for people to look over and find out if I'm on the right track. I'll work on making it smaller later. I'm definitely not sure if I did the connection from the middle connection of the triac to the out & the resistor. That looks weird but from Don's picture I figured that's how it would look with traces.

Also does anyone know if this was done before? I figure no reason to reinvent the wheel if someone already made a PCB design. Don did say he thinks someone did do this board before but I couldn't find it in the forums. I did find it talked about a little here and there but nothing solid of someone else repeating it.

Thanks for any advice.

Jason

Inline SSR v1

48 Replies
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

I have one, but I thinks its in an older program. I'll see what I can find.

Edit: Found it. It was done with PCB Artist. I have attached the Printout, Etch PDF, and PCB Artist files. PCB Artist is from Advanced Circuit and the version I used was free.

Keep in mind this was not checked by any experts here. It was the first board that I designed on my own and actually turned into a Home-etched one. I etched a bunch of these and ended up soldering up 12 of them. I had 4 of them working perfectly as a test One 4 Channel Chase Cycle string 🙂

You will see extra holes on the board. Those were so that I didn't have to do any wiring and thse could truly be inline. I also had an inline fuse for every 4 channels.


Reply
Posts: 4092
(@skunberg)
Famed Member
Joined: 18 years ago

I have made a couple from strip exactly like Don's. I need between 20 and 40. Very slow going to make them this way. But a pre made board would help alot. I'm not sure if we can get enough interest to make a board run worth while. But maybe we can get a few sample boards. At the small size we're talking about maybe 50 of them on a board (5 the long way x 10 the short way). Have them well scored so they break apart easy. Maybe two sided to keep the size down and keep the traces big enough. I've never designed a board either but i've watched on the sidelines as a few became a product.

Brian


Reply
Posts: 1041
(@n1ist)
Noble Member
Joined: 19 years ago

A few tips:

- Make the AC wiring thick enough to handle your expected current, with suitable margin.
- DO NOT run any traces under the opto, and keep all AC traces at least a quarter inch away from the low voltage side. Otherwise, the traces may be close enough to arc over
- The holes for the wires must be large enough for the wire to fit through, and have enough of a solder pad to secure the wire. If you have space, add an extra hole or two next to the wire terminal so you can strain-relieve the connection by looping the wire thru the extra hole before soldering it
- Optos have 6 pins, even if you are only using 5.
- Avoid having traces that connect to other traces or pads at acute angles; the sharper the angle, the more chance of getting an acid trap. Likewise, it is better to bend traces with two 45 degree bends rather than one square corner
- Think about the form factor; square boards are good to mount in a box (don't forget mounting holes) while longer skinny ones are good candidates to be heatshrunk as a lump on a cable

/mike


Reply
Posts: 58
(@vincehc)
Trusted Member
Joined: 18 years ago

I am working on a project that I needed some pcbs made and a friend recommend the following site http://www.seeedstudio.com/depot/fusion-pcb-service-p-835.html?cPath=185 they start at 9.99 for 10 5cm by 5 cm boards with no setup Fee I plan on doing my order in feb when they start taking orders again. Closed till then for the Chinese holidays


Reply
Page 1 / 10
Share: