FPP PB16 Pixel Cont...
 
Notifications
Clear all

FPP PB16 Pixel Controller

630 Posts
62 Users
6 Reactions
389.5 K Views
DrNeutron
Posts: 2017
(@drneutron)
Noble Member
Joined: 14 years ago
Supergumby wrote:Scott,
The new 16_Expansion layout is perfect. I see that you have flipped the headers on the remaining expansion boards as well.

To complete the PB16 DIY controller family, what would be your interest in mocking up a four-out Differential Receiver board?

Don

I think that would be a great addition.....also have you considered making a receiver board? Love the idea of using differential outputs to receivers in areas far away....

Sent from my SM-G955W using Tapatalk


Reply
Posts: 87
Topic starter
(@scooter-seh)
Trusted Member
Joined: 12 years ago

I assume you are going to want a 16 port Differential Expansion too.

Supergumby wrote:Scott,
The new 16_Expansion layout is perfect. I see that you have flipped the headers on the remaining expansion boards as well.

To complete the PB16 DIY controller family, what would be your interest in mocking up a four-out Differential Receiver board?

Don


Reply
Posts: 36
(@supergumby)
Eminent Member
Joined: 17 years ago
scooter_seh wrote:I assume you are going to want a 16 port Differential Expansion too.

So, I ran my first year of pixels this year using three PB16's, two 16_Expansions from one RasPi FPP, and the one thing I struggled with was distance to first node on different props I had built and scattered. I would like to reduce the number of buffer/line drivers needed for long wire runs.

My initial thought was to increase the land footprint of each PB16 by using 2 four port differential receivers driven by a multi-expansion board. That's 32 SPI outputs and 2 DMX per PB16, with 8 of those spread out up to ~250' east and west of the PB. While I could probably find a use for a 16 out differential receiver, it would mean development on both ends, including a four port differential expansion board - which, if developed, would probably be used in my yard to drive (4) four-port diff rec'rs.

Bottom line, if you lay out the boards, I'm going to build them and put them in the toolbox for whatever next year brings - more options is definitely better, but I'm not the one doing all the work (thanks again, by the way). This open-hardware paradigm is proving very productive.

Don


Reply
Posts: 58
(@cjaqua)
Trusted Member
Joined: 12 years ago
Supergumby wrote:So, I ran my first year of pixels this year using three PB16's, two 16_Expansions from one RasPi FPP, and the one thing I struggled with was distance to first node on different props I had built and scattered. I would like to reduce the number of buffer/line drivers needed for long wire runs.

My initial thought was to increase the land footprint of each PB16 by using 2 four port differential receivers driven by a multi-expansion board. That's 32 SPI outputs and 2 DMX per PB16, with 8 of those spread out up to ~250' east and west of the PB. While I could probably find a use for a 16 out differential receiver, it would mean development on both ends, including a four port differential expansion board - which, if developed, would probably be used in my yard to drive (4) four-port diff rec'rs.

Bottom line, if you lay out the boards, I'm going to build them and put them in the toolbox for whatever next year brings - more options is definitely better, but I'm not the one doing all the work (thanks again, by the way). This open-hardware paradigm is proving very productive.

Don

What size resistors are you using? That will play a big role in the distance you can get to the first pixel.


Reply
Posts: 36
(@supergumby)
Eminent Member
Joined: 17 years ago
Cjaqua wrote:What size resistors are you using? That will play a big role in the distance you can get to the first pixel.

I'm using the 150 Ohm SIPs that Scott designed in, I purposely didn't run more than 10 or 15 feet without a line driver, and on 18AWG - mostly out of an abundance of caution since this is my first year with pixels - and everything worked great.

Don


Reply
Page 14 / 126
Share: