Dancing Lights - GE...
 
Notifications
Clear all

Dancing Lights - GETTING STARTED....

61 Posts
14 Users
0 Reactions
20.8 K Views
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

From the COOP post...

Also, for those of you that are interested, I will also have pre-programmed PIC's availible, that way you do not need a seperate PIC programmer.

What does this mean for me? I'm a newbie and I know there was some aspect that needed to be programmed. Does this mean that I wouldn't have to worry about that.

Also...

This board is going to have a couple small changes made to it. I have tossed this idea around for a bit, and have decided to move forward. I am planning on change the output connectors from a screwdown terminal block to spade plugs. The board will accept EITHER screwdown terminals OR spade plugs.

Example part would be mouser 534-1287, the total cost for on-board connectors would be $5.30, compared to about $5.00 for the screw terminals, but, this would ALSO include a neutral bus, which is NOT on the current board.

Is this an extra or different part that would have to be purchased or will it be part of the board?

From the list of needed parts received yesterday, the pricing is pretty much the same, however, I could not find Mouser Part #584-SA105E104MAR, but there is a
581-SA105E104MARC. Is that the right part?

The help is APPRECIATED!


Reply
Posts: 37
(@frankz)
Eminent Member
Joined: 19 years ago
Superfreak3 wrote:From the COOP post...

Also, for those of you that are interested, I will also have pre-programmed PIC's availible, that way you do not need a seperate PIC programmer.

What does this mean for me? I'm a newbie and I know there was some aspect that needed to be programmed. Does this mean that I wouldn't have to worry about that.
The PIC is the chip that has to be programmed. It's on the BOM as part# 579-PIC16F688-I/P.
If you purchase it from Mouser, then you have to either have your own PIC programmer (a separate piece of hardware) or find someone to program it for you.
Or you can purchase it pre-programmed via the Coop, no need for a programmer since it's already done.

Superfreak3 wrote:
This board is going to have a couple small changes made to it. I have tossed this idea around for a bit, and have decided to move forward. I am planning on change the output connectors from a screwdown terminal block to spade plugs. The board will accept EITHER screwdown terminals OR spade plugs.

Example part would be mouser 534-1287, the total cost for on-board connectors would be $5.30, compared to about $5.00 for the screw terminals, but, this would ALSO include a neutral bus, which is NOT on the current board.

Is this an extra or different part that would have to be purchased or will it be part of the board?
Since he says it will accept either part, then it will be your choice as to which to use, one or the other.
If you look at the picture of the Ren24 in the wiki, you see the 6 screw terminals [labeled as outputs] on each of the 4 corners of the board. That is the output from the onboard ssr's that you will connect your light strings to.
The option is to use the original screw terminals as listed in the BOM, or replace them with the new spade plugs.

Superfreak3 wrote:
From the list of needed parts received yesterday, the pricing is pretty much the same, however, I could not find Mouser Part #584-SA105E104MAR, but there is a
581-SA105E104MARC. Is that the right part?

I think your part#584-... is a typo. It should be 581-....

.


Reply
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

Thanks for that info!!

😀 😀


Reply
Posts: 37
(@frankz)
Eminent Member
Joined: 19 years ago

I guess I should use the whole part #, to make sure there's no confusion:
I think
584-SA105E104MAR is a typo, and it should be
581-SA105E104MAR

I don't see that typo in the BOM in the wiki, so maybe you just wrote it down wrong.
.


Reply
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

The erroneous part number was contained in an .xls spreadsheet that I was linked to in the chat room.

If the wiki is correct, I'll just go with that. I think on Mouser though the part number ended MARC not MAR.

Here is another quick question...

Yes, it has 24 channels to controll 24 different sets of lights. and you you can string more then one string of lights on the same channel.. just dont go over 1A per channel (most mini light 100 ct strings are about .3A)

What happens if I exceed 1A on a given channel. Do I blow out or permanently loose that channel or does it fry the board in some way?

Also, what load does a typical blow mold with a 40 or 60 watt bulb carry? Would it be 40 watts / 120 volts?


Reply
Posts: 37
(@frankz)
Eminent Member
Joined: 19 years ago
Superfreak3 wrote:The erroneous part number was contained in an .xls spreadsheet that I was linked to in the chat room.

If the wiki is correct, I'll just go with that. I think on Mouser though the part number ended MARC not MAR.

So somebody needs to correct their spreadsheet, then.
Mouser site shows both ...mar and ...marc. ...mar is in stock, ...marc is not in stock and appears to be packaged differently.

Superfreak3 wrote:
Also, what load does a typical blow mold with a 40 or 60 watt bulb carry? Would it be 40 watts / 120 volts?

Yes. 60 watt bulb / 120v = 0.50amp
Power useage should be listed on a label on the power cord of most decorations.
Here's a good table showing the typical power requirements of many different things:
http://www.planetchristmas.com/FigurePower.htm

.


Reply
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

I guess I should get some soldering gear together as well:

Soldering Iron, Solder, etc.

With the solder, what is the redommended alloy, diameter, weight, core size?

Is there a listing of items I would need to assemble the board outside of the component listing for the Ren 24?

I read somewhere that one shouldn't use a soldering iron over 30W because you might damage the board. Is this true?

Man, I sure hope I can get this together without burning the house down!

Any further help is greatly appreciated!


Reply
Posts: 999
(@ppohlman)
Noble Member
Joined: 19 years ago
Superfreak3 wrote:Any further help is greatly appreciated!

Check out the soldering help on the wiki. It's pretty informative.
http://curiousinventor.com/guides/How_To_Solder


Reply
Posts: 934
Topic starter
(@superfreak3)
Noble Member
Joined: 19 years ago

That is great information.

It looks as though a fairly cheap soldering iron will do the trick (I was thinking of getting a soldering starter kit that includes a 30W soldering iron. Would that be OK or should I look into a soldering iron station with some form of temperature control?). I wonder what solder is best to use based on size, alloy, etc. Is it safe to say that the size/type mentioned sufficient for most jobs will be OK to construct the Ren 24: 1/32(.03) rosin-cored 60/40 or should I get the lead free?

If lead free, what are the drawbacks if any besides higher melting point/longer joint time?

Also, should I get a solder wick to clean up any mistakes, if it can in fact be used for that purpose?


Reply
Posts: 999
(@ppohlman)
Noble Member
Joined: 19 years ago
Superfreak3 wrote:1/32(.03) rosin-cored 60/40

Yeah, that sounds like a good one. The rosin-core helps in the soldering process.

The higher melting point is the only drawback that I know of with the lead free.

Superfreak3 wrote:Also, should I get a solder wick?

Yes. Solder wick is the perfect thing for cleaning up mistakes. Anyone soldering for the first time will probably use it. I have.


Reply
Page 3 / 7
Share: