Welder, now what?
 
Notifications
Clear all

Welder, now what?

29 Posts
19 Users
0 Reactions
13.6 K Views
rjchu
Posts: 1191
Topic starter
(@rjchu)
Noble Member
Joined: 17 years ago
[#35292]

Wife got me one of these for Christmas http://t.harborfreight.com/90-amp-ac-120-volt-flux-cored-welder-61849.html

From what I can tell, the preferred material to craft wire frames and such from is 1/8" round rod/wire. Where can this be sourced at a reasonable price, what material should I be looking for since this apparently isn't suitable for stainless steel, and lastly what paint or other coating do you guys use to weatherproof your creations?

Thanks,

-joni-


28 Replies
imbluenote
Posts: 1615
(@imbluenote)
Noble Member
Joined: 15 years ago

Comments from a complete newbie/amature welder

i have a similar one from sears.

I made a few snowflakes and have other projects i haven't gotten around to yet. I used 1/4" rod. I would look for a metal supply company, the box stores prices are high for any quantity of rod. I was also going to try 3/8" rebar to see how well that would weld with one of these. As far as coating, i did several layers of spray paint, i haven't noticed any real problems yet, but i do have a spot or two at the welds i usually give a shot of paint every year, i think i used cheap paint on the flakes though, a quality brand would probably hold up better.

If you don't already have one i would get an angle grinder (HF as well) the flux core splatters alot when welding so you'll want to clean that up. You may want it to clean up the welds too if you have a problem at a weld.

Also check your walmart for extra welding wire. For some reason the one by me has it and at the best price i have found, but i have only found it in that one wal-mart. I am sure there are others that have it though.


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago

Cool!

Exact same situation, but with one of these:
http://www.homedepot.com/p/Lincoln-Electric-AC225S-Arc-Welder-K1170/100041326

I see this is actually fairly high-end for an AC-only welder. I plan to use it to make stands and frames, structural support for props, maybe some limited metal furniture. I don't particularly like working on cars, though I'll probably do some sort of railing system on my truck bed.

Am I going to be satisfied with an AC welder, or should I exchange for AC/DC? Or even AC/DC/TIG?


Reply
Posts: 2048
(@scootchu)
Noble Member
Joined: 17 years ago

I have a Lincoln Mig and used 1/4" rod. Soft enough to bend easily and thick enough to weld and stand up straight. The welder you have will be fine, just have to clean the welds afterwards. I went with flat black spray can paint and after three seasons they hold up well.


Reply
Posts: 242
(@hockeyhunter1956)
Reputable Member
Joined: 13 years ago

This was my first year building wire frames for decorations. I used a local steel supply business to purchase my 1/4" cold roll. That has worked out to be good material for me to bend and cut into the shapes I designed. I made about 20 life size nativity and Alaska animals. Since I had access to a paint shop at work, I had the frames sandblasted, heavy duty coating industrial coatings for the primer and finish coat applied. I'm expecting that these frames will outlast me. before they begin to rust.

I only wanted to build and wire these frames once.

At a minimum I would be careful with making sure everything gets a good coat of primer and a couple of coats of a quality spray paint for finish.


Reply
IaRoadKill
Posts: 586
(@iaroadkill)
Honorable Member
Joined: 12 years ago

And don't forget to remove any weld splatter/sharp spots on your creation. Anything that could hook and cut a wire.
Just saying…


Reply
derekbackus
Posts: 565
(@derekbackus)
Honorable Member
Joined: 15 years ago
deonb wrote:Am I going to be satisfied with an AC welder, or should I exchange for AC/DC? Or even AC/DC/TIG?

I would recommend returning it. Get the best welder you can afford. I'd suggest a MIG welder. MIG welders for feed wire through the wand and are fairly easy to learn how to use.

The welder you have is called a "stick" welder and is typically use for heavier gauge metals.


Reply
Posts: 146
 Dan@
(@dan-2)
Estimable Member
Joined: 14 years ago

I would return. Get a MIG welder that uses gas (75/25) as the shielding. The flux core just makes a bigger mess and requires more cleanup.


Reply
Posts: 1115
(@11bravo)
Noble Member
Joined: 14 years ago

If you can budget one, a gas MIG welder is the way to go when welding wire frames and sheet metal. Very easy to weld with over a stick welder. Plus a stick welder may not be able to get low enough in amperage without blowing thru the metal.

I have a Miller 135 gas welder. It is 120volt and can do 3/16" metal easy. It will do up to 1/4" metal if you don't bog it down. Just do short welds at a time on 1/4" flat bar and angle iron. It will do 1/4" rod with no problem since you don't have to make long welds.


Reply
Posts: 1159
(@deonb)
Noble Member
Joined: 13 years ago
derekbackus wrote:I would recommend returning it. Get the best welder you can afford. I'd suggest a MIG welder. MIG welders for feed wire through the wand and are fairly easy to learn how to use.

The welder you have is called a "stick" welder and is typically use for heavier gauge metals.

Ok, thanks. This helps a lot. How about TIG? At what point is TIG more appropriate than MIG or ARC?


Reply
Page 1 / 3
Share: