2015 Bethlehem Star
 
Notifications
Clear all

2015 Bethlehem Star

117 Posts
15 Users
0 Reactions
44.4 K Views
IaRoadKill
Posts: 586
Topic starter
(@iaroadkill)
Honorable Member
Joined: 12 years ago

Hi LightUp

lightup wrote:both circuits can do dimming.
Current rating for the 1st one is 1a, the 2nd one i didn't know which triac was used so can't say its current rating.
image

..................................................

image

.......

image

....

image

Triac is BTA06-600CW. _____Can I substitute an H11AA1 for the MOC3023 in this circuit?

image

The instructions (?) for the second one say to connect +5V and data
That seems wrong to me. Shouldn't it be Data and Ground?

I am using it with a Ren32.
Output Jack Pin Assignments
Pin# Signal
1 +5VDC
2 First Output Channel
3 Not Connected
4 Second Output Channel
5 Not Connected
6 Third Output Channel
7 Signal Ground
6 Fourth Output Channel
Each of the 8 output jacks control 4 channels each.

So for my 1st channel, should I use pins 1&2 or pins 2&7?


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago
IaRoadKill wrote:...Triac is BTA06-600CW. _____Can I substitute an H11AA1 for the MOC3023 in this circuit?

No, you may not. 🙂 It changes the way things work.
The BTA06-600 is a 6A, so it has the oomph...

...The instructions (?) for the second one say to connect +5V and data
That seems wrong to me. Shouldn't it be Data and Ground?

Ahh... the mysteries of electronics.
No, the diagram is correct. The +5V applies power to the little photo diode inside the chip. Pin 1 is the anode. Then to cause light flow out of the diode you need to "ground" pin 2 through a current limiting resistor. Hence they call it "data" because you will be applying this "ground" rapidly in an ON-OFF fashion, also know as PWM.
You may think of this operation as similarly used for "dumb RGB" type lights, but in this case it is only 1 "dumb" light. 🙂
With regards to your ground, that is the ground of the +5V power supply - which is part of your "data" signal, which swings 0V (ground) to +5V.

...I am using it with a Ren32.
Output Jack Pin Assignments
Pin# Signal
1 +5VDC
2 First Output Channel
3 Not Connected
4 Second Output Channel
5 Not Connected
6 Third Output Channel
7 Signal Ground
6 Fourth Output Channel
Each of the 8 output jacks control 4 channels each.

So for my 1st channel, should I use pins 1&2 or pins 2&7?

Yes and no.
The 1st channel uses 1 & 2,
The 2nd channel uses 1 & 4,
The 3rd channel uses 1 & 6,
The 4th channel uses 1 & 8.

The "common" in this case is +5V, rather than ground - hence your confusion. Think of the pathway as electron flow. It may make more sense to you. Each data line starts at "ground" and electrons flow through the series resistor then photo diode then to +5V of the power supply. For electrons to flow you need a potential difference.
OK, I'll stop here, 'nuf said...


Reply
IaRoadKill
Posts: 586
Topic starter
(@iaroadkill)
Honorable Member
Joined: 12 years ago
LightUp wrote:

Ahh... the mysteries of electronics.
OK, I'll stop here, 'nuf said...

You must have some "Teacher" blood in you! :thup:
That was awesome.
Thank you


Reply
IaRoadKill
Posts: 586
Topic starter
(@iaroadkill)
Honorable Member
Joined: 12 years ago

So if I paid attention in class...:wink:

With this SSR...

image
image

The square "G" pad (green wire in 2nd picture) should be signal (pin2)
and
the round "+" pad (orange wire in the second picture) should be the +5V (pin1).

How'd I do teach?


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago
IaRoadKill wrote:You must have some "Teacher" blood in you! :thup:
That was awesome.
Thank you

Yes, but not officially....


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago
IaRoadKill wrote:So if I paid attention in class...:wink:

With this SSR...

The square "G" pad (green wire in 2nd picture) should be signal (pin2)
and
the round "+" pad (orange wire in the second picture) should be the +5V (pin1).

How'd I do teach?

I can't really say since your "report" is fuzzy... 🙂
I don't have a schematic, nor a board layout pattern to follow. So I can't tell how it is wired.
From the VO2223 datasheet, pin 2 of the chip is the anode, or positive side and the cathode connects to pins 1,3 & 4.
But I can't tell from your picture whether your board requires a current "source" or a current "sink" configuration.
Once I see the schematic of your little board (or its tracks) I may be able to advise you.


Reply
IaRoadKill
Posts: 586
Topic starter
(@iaroadkill)
Honorable Member
Joined: 12 years ago
LightUp wrote:I can't really say since your "report" is fuzzy... 🙂
I don't have a schematic, nor a board layout pattern to follow. So I can't tell how it is wired.
From the VO2223 datasheet, pin 2 of the chip is the anode, or positive side and the cathode connects to pins 1,3 & 4.
But I can't tell from your picture whether your board requires a current "source" or a current "sink" configuration.
Once I see the schematic of your little board (or its tracks) I may be able to advise you.
image
image
image

Sorry about the first 2 pictures are upside down. :devilred: (Added challenge)

My drawing should be correct.


Reply
Posts: 2541
(@lightup)
Famed Member
Joined: 17 years ago
IaRoadKill wrote:

Sorry about the first 2 pictures are upside down. :devilred: (Added challenge)

My drawing should be correct.

Hehe... I just rotated my laptop to see the picture. You thought I lived in Australia, right? 🙂
OK, this connection is similar to your previous designs.
"+" is your +5V line.
"G" is your channel data line.

It appears that these designs like to have, LOW, "ground", as turning lights ON, like the mechanical SainSmart relays.
And use "HIGH" to turn OFF the lights. So you may need inversion, of say Vixen channel data, in your controller.


Reply
IaRoadKill
Posts: 586
Topic starter
(@iaroadkill)
Honorable Member
Joined: 12 years ago
LightUp wrote:

It appears that these designs like to have, LOW, "ground", as turning lights ON, like the mechanical SainSmart relays.
And use "HIGH" to turn OFF the lights. So you may need inversion, of say Vixen channel data, in your controller.

My first attempt at building a chase-cicle SSR worked!
(It took me 2-1/2 hrs to build that little $@&&*#%.

It seems that Vixen3, Ren32 and chase-cicle work correctly together.

I'm going to finish off a Cuba Libre and then try the SCISSR again.


Reply
IaRoadKill
Posts: 586
Topic starter
(@iaroadkill)
Honorable Member
Joined: 12 years ago
LightUp wrote:
OK, this connection is similar to your previous designs.
"+" is your +5V line.
"G" is your channel data line.

YEA! This one works too!

Time for another Cuba Libre!:freak:


Reply
Page 4 / 12
Share: