This is embarrassing to ask, because I knew how to do this, but haven't needed to for years, relying on the initial configuration. So somehow, that config is gone, and I need a refresher. I have a pixel column with a total of 180 pixels in a zig zag setup 3 wide. So starting top left, 60 top to bottom, then 60 bottom to top, then 60 back down. I then have it divided into upper column and lower column. But I have the full length of 60 pixels high divided into 10 groups. Each group gets 6 pixels, and the same 6 pixels on both the lines beside it for a total of 18 pixels per group. Somehow, the previous config is gone, and now when I patch it straight to the controller, it treats 18 pixels vertically in a row as a group. So I need an effect for example placed on the very bottom group 1, to light up technically pixels 55-60, 61-66 and 175-180. Please remind me how I would patch this correctly? It looks fine in the preview since I linked the elements that way, but that obviously doesn't help the true output
It mayyyy be coming back to me.... I think... So in that example I would patch those three pixel ranges to consecutive channels right? So 18 or technically 54 channels in a row starting at 61-66, then 61-66, then 175-180? In the sequencer, the groups are lowest to highest top to bottom, but physically start is top left. Would I want to start patch at channel 1 for group 10 at the top? Or other way around? I seem to recall this was a pain in the ass when I had to do it lol
You can patch all 180 pixels in order but reverse patch pixels 61-120. Where you need to be is in the grouping. If you only want the bottom half to light then you need to group only those pixels.
Sent from my SM-T710 using Tapatalk
pmiller wrote:You can patch all 180 pixels in order but reverse patch pixels 61-120. Where you need to be is in the grouping. If you only want the bottom half to light then you need to group only those pixels.Sent from my SM-T710 using Tapatalk
Just to confirm I'm not misunderstanding, by grouping you are talking about the hierarchy in the sequencer right? Like in my case I have it column-->upper column-->groups 1-5 and then the same for bottom column. Then, in the individual groups, I place the 6 pixels from the first string and the six from string and three for 18 per group. That's how it's currently setup. But it plays back groups that should be 6 tall x 3 wide as 18 vertical pixels in a row when patched straight through
XmasinVancouver wrote:Just to confirm I'm not misunderstanding, by grouping you are talking about the hierarchy in the sequencer right? Like in my case I have it column-->upper column-->groups 1-5 and then the same for bottom column. Then, in the individual groups, I place the 6 pixels from the first string and the six from string and three for 18 per group. That's how it's currently setup. But it plays back groups that should be 6 tall x 3 wide as 18 vertical pixels in a row when patched straight through
Including the reverse for the middle of course, but that would hardly affect 18 pixels lighting up together on string one right
Also, something I've never thought to actually setup manually, because it seems to often just show up...Could the Grid property in setup be helpful here? When I try it, it knows the group I've selected needs to be 18 and it says width x height as long as it equals 18. I don't know how that would work in tandem with patching though. Something I love about Vixen, even after years, I always find new cool stuff lol
XmasinVancouver wrote:Including the reverse for the middle of course, but that would hardly affect 18 pixels lighting up together on string one right
Not unless they are grouped incorrectly. Are you sure you don't have those 18 grouped together with others? Also, instead of using hierarchy, apply the effect to the group only and see what happens. I have an issue with identifying Vixen using element designation. I prefer using you have a main folder. Inside that folder are groups called normal and split (just naming something you can relate too). When you apply an effect to the main folder you then can choose the level at which that effect applies. I've always had issue with things not working right because it seems to me the effect is applied to everything in that main folder. So, I will place both the normal and split on the main level making them independent of the main folder. Then everything I did worked as it should.
I had a folder called Pixel Trees. Inside that folder I had Pixel Tree 1 and Pixel Tree 2. When I applied an effect to the main folder I expected both trees to do the exact same thing. Nope, that didn't happen. It was like Vixen applied the effect across both trees as one and I had random quirks going on. It didn't matter what effect I used the same thing happened. So I decided to duplicate each tree outside the main folder and walla, they both worked correctly. I did have to copy and paste the effect for each but it worked. I kept he original folder for effects like set level.
Sent from my SM-T710 using Tapatalk
BTW. When you patch in reverse order select "Reverse Element Order" on the left side of the patching screen. Don"t use "Reverse order of selected outputs" on the right side. Also, always remember when Reversing element order whenever you patch something else, uncheck that box. It does not default back to the original unchecked box. I got messed up many times not catching that.
