Switching resolutio...
 
Notifications
Clear all

Switching resolution

11 Posts
7 Users
0 Reactions
6,719 Views
Posts: 3650
Topic starter
(@jhinkle)
Famed Member
Joined: 15 years ago
[#18434]

I'm new to Vixen. I don't know version 2 - waiting on 3.

I've search and can't find the answer - so I'll ask.

Once you start building a sequence in Vixen, you chose 25, 50, or 100 msec .... does Vixen allow you to change timing mid-stream?

If so - how does it handle command overlaps when going from 25 to 100 for example? You might have 4 different commands, each in adjacent 25 msec slots that are now compressed into a single 100.

Thanks.

Joe


10 Replies
kychristmas
Posts: 3955
(@kychristmas)
Famed Member
Joined: 18 years ago

In Vixen 2.x you can change after the fact. I do it when I copy from other people's sequences. Since I only copy sections, I usually switch the source sequence to my 50ms standard. I don't believe it applies any compression algorithms. I think it's difficult to change the resolution to 25% without losing quality, but I recall it does a pretty good Job.

Kelly


Reply
51fordf2
Posts: 1280
(@51fordf2)
Noble Member
Joined: 18 years ago
JHinkle wrote:Once you start building a sequence in Vixen, you chose 25, 50, or 100 msec .... does Vixen allow you to change timing mid-stream?

Thanks.

Joe

Joe - this is NOT meant to sound flippant, or anything. From MY experience, I found it easiest to spend some time with Vixen, just trying everything I could find in it - and see what it does. I learned a heckuva lot, by doing that, and as it turned out, I did a lot of things second nature, then read later about how a lot of people, didn't even know that feature existed, such as copying and loading routines, and a few other "goodies". I recommend that you make up a couple quick and dirty routines, one at, say, 100 msec, and another at 25 msec, and import parts of each, back and forth between sequences (copy and paste a quick routine from the 25 to 100, and a part from the 100 to the 25), and see what they do. I don't have my Vixen, or my sequences here, but I DO recall, doing an entire sequence in one "speed" and then changing it to another, and had to do a lot of "fine tuning" to get it just right. But then, I've been known to spend WAY too much time, when it isn't necessary. I realized that this year, when I had one sequence, that I basically banged out in about an hour (normally they take hours - LOT'S of hours!!), and nobody could tell the difference! We tend to be our own worse critics...

Anyway, that's my recommendation, one that helped me a lot, throughout Vixen. Not that I DIDN'T gain a bunch, by reading what others did. There's just SO much to learn!

Mostly, enjoy!

R


Reply
TimW
Posts: 554
 TimW
(@timw)
Honorable Member
Joined: 19 years ago

As I understand it, in pre V3 vixen its a grid - with a defined resolution. You can't change mid sequence, the intervals is set uniquely for each song.

You can modify the resolution (globally) and I assume you can cut and paste slices in and out.

When you say 'commands'... Does that mean 'values'? Generally that's all that is stored in the grid?


Reply
Posts: 3650
Topic starter
(@jhinkle)
Famed Member
Joined: 15 years ago

Thanks for all the replies.

I was asking so when I started my first song sequence and possibly decided to change timing after hours of work - was it possible.

I take from the replies - yes - with rework required.

I used the word command (for lack of a better choice) because the values are the result of a command --- as in chase - results in many values. I suspect Vixen internally saves what I call commands and thereby produces values when required.

When increasing timings - say from 25 to 50 - then you may have overlapping commands that want to generate a value for the same cell (since the number of cells were reduced by half).

I was asking what the outcome was to be -- as some has stated - rework.

Moral of my story/question - select properly at start grasshopper.

Joe

Thanks.


Reply
Page 1 / 3
Share: