Cutting Pixels or A...
 
Notifications
Clear all

Cutting Pixels or Adjust Spacing

4 Posts
3 Users
0 Reactions
1,627 Views
 munu
(@munu)
Posts: 427
Honorable Member
Topic starter
 
[#55052]

I plan to use pixels for the first time this year around my windows and front door. I bought some from Ray but I wonder if you are stretching them and keep them at the planned length (4"-5") or if you are adjusting/shortening the distance so you can use whole strings.

How about if you have props that just need a few pixels? I have some "snow flakes" from HolidayCoro that just need 18 pixels. Are you just going from one snow flake to the next using one string and leave a few pixels between the snow flakes or are you cutting them all to the exact 18 pixels and put some custom cable in between?

If you cut pixel strings, are you using the reminder to build other props, possibly even combining two or more cut off pieces? I have some small PCB boards that I could possibly use to combine strings.


 
Posted : 28/11/2021 4:32 pm
(@ezellner)
Posts: 740
Prominent Member
 

Distance between pixels is really determined by how you want them to look from the distance they will normally be viewed. It rarely works out to an exact match to a string of 50 (or multiple thereof) so you either cut or connect additional pixels together. Use connectors to connect them or solder together with heat shrink to provide weather resistance.


Ed
Happily retired :biggrin:

 
Posted : 28/11/2021 4:43 pm
TomL8345
(@toml8345)
Posts: 1356
Noble Member
 
munu wrote:I plan to use pixels for the first time this year around my windows and front door. I bought some from Ray but I wonder if you are stretching them and keep them at the planned length (4"-5") or if you are adjusting/shortening the distance so you can use whole strings.

How about if you have props that just need a few pixels? I have some "snow flakes" from HolidayCoro that just need 18 pixels. Are you just going from one snow flake to the next using one string and leave a few pixels between the snow flakes or are you cutting them all to the exact 18 pixels and put some custom cable in between?

If you cut pixel strings, are you using the reminder to build other props, possibly even combining two or more cut off pieces? I have some small PCB boards that I could possibly use to combine strings.

You can cut pixel nodes to any length you need, or splice on more nodes if needed. I always have a connector at the beginning and end of each prop. If needed you can also splice in extra wire between pixels to make a longer reach between pixels ( I use 18 AWG wire). Most of my pixels have a 2" spacing on my props, but I do NOT cut the extra between the pixels. (Too many possible points of failure and WAY too much work). You can absolutely use the left over pixels you cut off a string on another prop, just remember there is an input and output side to each node.

HTH


2012 - 1st year 64 Channels - 7500 LED lights - 5 sequences
2013 - 128 Channels - 10,000 LED lights - 7 sequences (2 New)
2014 - 201 Channels - upgrading 8 Arches to dumb RGB - 8+ sequences (1+ New)
2015 - 240 Channels + 8 Universes - sequences TBD
2016 - No Display :ohwell:
2017 - Back in the Game - 240 Renard Channels + 12 Universes
2018 - 256 Renard and 9 Falcon Outputs of Pixels - 16 sequences shown over 2 nights
2019 - 256 Renard and 9 Falcon Outputs of Pixels - 16 sequences shown over 2 nights
2020 - Emergency Conversion to Falcon F48 with limited wireless
2021 - 10 RHL Simple Pi Pixel Controllers - 1 Master with 9 Remotes

 
Posted : 29/11/2021 9:56 am
 munu
(@munu)
Posts: 427
Honorable Member
Topic starter
 

Thanks for all the input. I will cut them up into sets of 18 and connect them with 16/4 wire that I have available (18/3 and 16/3 is hard to find in long lengths). I am not sure I will put connectors on it. I might just solder them because they will stay together. For other props I will use connectors based on your suggestions.


 
Posted : 29/11/2021 4:06 pm
Share: