1st Mega Tree
 
Notifications
Clear all

1st Mega Tree

17 Posts
13 Users
0 Reactions
10.1 K Views
kidcole
Posts: 307
(@kidcole)
Reputable Member
Joined: 17 years ago
Wolfie wrote:You have many things to consider, preferably before you buy anything.

First is the controller. I know you say you want an E682. Why? Why that specific controller? If you are looking at something you can kit build, then thats a reasonable choice. However, if you can spring about $20 more on the controller, you can get a Falcon F16v2 very shortly (end of the month) or a v3 later in spring. The Falcon is a far better controller with way more capabilities than the 682. Its well worth more than the $20 difference to be quite honest. Do you need that capability for just a megatree? No, quite unlikely. However, the long term payout is quite likely very much a "I wish I had" scenario. Many people are happy with the 682. Many are happy with the Falcons. I am just saying you might want to look into your options before comitting to one now.

Next is software choice. Vixen is not bad at all. Its a solid package and, for me, was pretty easy to learn on. However, I would recommend you also look at xLights. Its learning curve is a bit steeper I will admit. But, its ability to deliver quality on your lights is definitely worth the learning investment. I started with Vixen. I used xLights last year so I have personally used both. And, if I had to start all over again, I would choose xLights to begin with. Both have progressed since I began with each one, but the rate of progress is substantially greater on xLights. Its also WAY easier to share sequences from others and get them working on your layout with xLights than it is in Vixen. If I did something on my 24x60 megatree in vixen you would put great effort to get it to run on your 16x50 and thats not the case with xLights. There are many free and for-purchase sequences available for xLights and that is not the case with Vixen. Looking at other's sequences is a very good learning tool which isn't very easy to do in Vixen. All I am saying is try both. Its ok to install both and try both at the same time. Then choose which you would like to go forward with.

Have you decided on a method of supporting your strings? I would highly recommend you ignore the copies and knockoff strips and go with Boscoyo pixel strips (boscoyostudio.com).

What about support pole system? Have you looked into how you are going to hold the thing up? If not, look through the many ideas here on the forum. Also, look into the JUMP and ASAP pole systems by Walter Monkhouse. And the Portable Hole bases also by Walter. (These are things you build, not buy)

Another thing you may wish to look into is the Christmas Expo coming up this summer. You can learn a heck of a lot from the seminars there as well as shaking hands and seeing faces of many here as well as vendors you might be considering buying from.

This is a very nice summary. I agree with all of it. I have a bunch of Sandevices and there is certainly nothing wrong with buying them. But the Falcon gear is technically WAY ahead of all the controller manufacturers with their FPGA-based design. A single Falcon F16 V2 or V3 is an amazing home base for any display. As you should do with any controllers you buy, give some consideration for having a spare in case you suffer an issue.

Xlights has a team of very aggressive programmers who are expanding leaps and bounds. also gives you the simple option of using the Falcon Pi Player (FPP) software to run your whole show on low cost Raspberry Pi computers. Falcon makes a PiCap card that daughters on a PI. The PiCap has two pixel outputs capable of 800 pixels each AND gives you a DMX out. All for $35 (plus the Pi).


Reply
Posts: 17
Topic starter
(@gocwbys)
Eminent Member
Joined: 10 years ago

Wow! Thanks for all the great advice! I am not committed to anything yet but the fact I want the first Mega Tree in my city...

Software: Vixen - xLights - either would be fine - Soundslike xLights (can i get a link to download the software?)

Controller: I know i need a E1.31 controller, I also saw the HinksPix16 for about $ 150.00 on holidaycoro - I just need something to get my feet wet and control the tree, would like to be able to add additional controllers as i will expand this project "hopefully" each year.

Pixels - Should i go with 5V or 12V ? I like 5V as it uses let juice. On my current pixel matrix 5V seems to power 100 pixels just fine.

String Supports - thanks for the tip. I will look for the boscoyostudio.com strips

Pole system - Total DIY - currently have a tree with Dumb Leds - will re use it most likely


Reply
stallionent
Posts: 1460
(@stallionent)
Noble Member
Joined: 13 years ago

Software: xLights (free download)

Controller: F16 V2 or V3

Pixels: 12V bullets

String Supports: boscoyostudio.com

My Mega tree thread: http://doityourselfchristmas.com/forums/showthread.php?42600-Project-180-x-10-ft-Mega-Tree&highlight=mega+tree Many changes, read entire thread.


Reply
Wolfie
Posts: 2225
(@wolfie)
Noble Member
Joined: 11 years ago

xlights.org


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
gocwbys wrote:Wow! Thanks for all the great advice! I am not committed to anything yet but the fact I want the first Mega Tree in my city...

Software: Vixen - xLights - either would be fine - Soundslike xLights (can i get a link to download the software?)

Controller: I know i need a E1.31 controller, I also saw the HinksPix16 for about $ 150.00 on holidaycoro - I just need something to get my feet wet and control the tree, would like to be able to add additional controllers as i will expand this project "hopefully" each year.

Pixels - Should i go with 5V or 12V ? I like 5V as it uses let juice. On my current pixel matrix 5V seems to power 100 pixels just fine.

String Supports - thanks for the tip. I will look for the boscoyostudio.com strips

Pole system - Total DIY - currently have a tree with Dumb Leds - will re use it most likely

Getting a HinksPix16 you will thank yourself for doing so !


Reply
Page 2 / 4
Share: