Man that is a super sweet offer. I will give you the low down on the stages of this. So my show computer was super basic I only used it for the show. It had windows xp. I was using the DE9 connector from my cpu to cat 5 onto the renard board worked amazing. I would love to get that drive back but here is where I am at I went and purchased a hp laptop and bought the USB adapter. I have been trying for 4 days to get my laptop to communicate with the renard board 0 luck I really was at the point of giving up. Like I said I really liked using the de9 connector seemed to have 0 issues. I cut my cable to make the usb adapter so I would have to remake that but I think it was 2 wires super easy. That is where I am at I am open to all options since I cannot get the laptop to communicate with the Renard. With that said this community is truly amazing I thank you for any help I can get at this point.
I can check when I'm at the office tomorrow to see what's there. I know there are quite a few PC's that run Windows 10 natively and would work fine for your show. I run my show directly from DE9 to ethernet from the PC to the first Renard, then it converts it to rs485 to each subsequent controller. I'm still using dumb RGB "super strips" as floods on the house that are powered by a Ren48LSD. Still 88 renard channels on my modern show, lol. I bet I have a PCIE serial card that would work on any of the PCs I have too.
Just out of curiosity, what USB to serial adapter are you trying to use? Did Windows get the drivers installed for it correctly?
MartinMueller2003 wrote:
We have no idea what the real issue is. We have yet to see the patching screens. No one has seen a test sequence. The OP stated that he cut both ends of the cable, you only need to cut the end that connects to the USB adapter. Even if the patching is wrong, as long as the controller has more than 1 channel defined and is enabled, you should see the RX led light up.Lights start with seeing the controller Config and a picture of the USB adapter with the wire attached. Then a picture of the other end of the cable and the jumper settings for the termination resistor.
I can definitely take some pictures when I get home of the usb adapter what I did with the wiring. Unless it is something in the laptop I purchased. I checked vixen everything seems right comm and all that. I have 6 renard 24s boards and tried all of them.
Did you check the com port settings in device manager on that laptop? It has to match the firmware as far as speed and the settings in Vixen in order to communicate properly. If I remember correctly, the port settings should be as follows.
Vixen needs to match that too and be set for the correct com port or you won't get anything out of it.
ptinhays wrote:
I can check when I'm at the office tomorrow to see what's there. I know there are quite a few PC's that run Windows 10 natively and would work fine for your show. I run my show directly from DE9 to ethernet from the PC to the first Renard, then it converts it to rs485 to each subsequent controller. I'm still using dumb RGB "super strips" as floods on the house that are powered by a Ren48LSD. Still 88 renard channels on my modern show, lol. I bet I have a PCIE serial card that would work on any of the PCs I have too.Just out of curiosity, what USB to serial adapter are you trying to use? Did Windows get the drivers installed for it correctly?
Here is the adapter I am using hope you can see it windows did not ask for a driver but it show on device manager as ports, usb serial port
ptinhays wrote:
I can check when I'm at the office tomorrow to see what's there. I know there are quite a few PC's that run Windows 10 natively and would work fine for your show. I run my show directly from DE9 to ethernet from the PC to the first Renard, then it converts it to rs485 to each subsequent controller. I'm still using dumb RGB "super strips" as floods on the house that are powered by a Ren48LSD. Still 88 renard channels on my modern show, lol. I bet I have a PCIE serial card that would work on any of the PCs I have too.Just out of curiosity, what USB to serial adapter are you trying to use? Did Windows get the drivers installed for it correctly?


