Been following the FM02 threads for sometime and not sure if I've seen someone with the same issue.
FM02, dipole antenna. When I connect a 3.5mm audio cable to input, I get a considerable increase in noise. This is even when the other end of the cable isn't connected to anything. When I unplug, noise goes away and everything is quiet on radio. When I use a lower quality cable, more noise (static and hum) exist. When I connect a higher quality audio cable ( http://www.monoprice.com/Product?c_id=102&cp_id=10218&cs_id=1021812&p_id=5581&seq=1&format=2 ) noise is reduced, but still audible. Does the same thing with either my dipole and/or the supplied antenna.
Any suggestions to try? Was thinking about hitting the audio input solder points with an iron.
aERonAUtical96 wrote:Been following the FM02 threads for sometime and not sure if I've seen someone with the same issue.FM02, dipole antenna. When I connect a 3.5mm audio cable to input, I get a considerable increase in noise. This is even when the other end of the cable isn't connected to anything. When I unplug, noise goes away and everything is quiet on radio. When I use a lower quality cable, more noise (static and hum) exist. When I connect a higher quality audio cable ( http://www.monoprice.com/Product?c_id=102&cp_id=10218&cs_id=1021812&p_id=5581&seq=1&format=2 ) noise is reduced, but still audible. Does the same thing with either my dipole and/or the supplied antenna.
Any suggestions to try? Was thinking about hitting the audio input solder points with an iron.
Is it open circuit noise? What if you shorted the input at the end of the cable and see if the noise reduces.
The source is to be a low impedance (<32 ohms) while an open (unterminated or unloaded) cable is a high impedance.
Sounds like the noise is coming in on your audio line so you might try using a ferrite core like the ones many times used on computer monitors. http://www.amazon.com/s/ref=nb_sb_ss_i_1_12?url=search-alias%3Daps&field-keywords=ferrite+core+filter&sprefix=ferrite+core%2Caps%2C219&rh=i%3Aaps%2Ck%3Aferrite+core+filter
I have a pack of http://www.amazon.com/gp/product/B007Q94CZM/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 and http://www.amazon.com/gp/product/B007Q94CJS/ref=oh_aui_search_detailpage?ie=UTF8&psc=1 on hand. My audio cable loops through a core about 3 times on each end (Pi w/ USB audio adapter to FM02) and it helped quite things does a lot. Anything around the wire? Power cables, etc?
But can a cable introduce noise when it isn't connected on the other end (i.e. no source)? I have a ferrite on the power. I can't put a ferrite on the thicker cable (don't have a ferrite that big). But I can switch audio cables and try it. I think I tried that last year and didn't get better results.
There are no other cables around and I make sure to avoid power cables as much as possible and cross at 90 degrees if I have to.
"Is it open circuit noise? What if you shorted the input at the end of the cable and see if the noise reduces." Not following here. Short the end that would normally connect to the audio source? Short it to what? Ground on the board?
Thanks,
aERonAUtical96 wrote:But can a cable introduce noise when it isn't connected on the other end (i.e. no source)? I have a ferrite on the power. I can't put a ferrite on the thicker cable (don't have a ferrite that big). But I can switch audio cables and try it. I think I tried that last year and didn't get better results.There are no other cables around and I make sure to avoid power cables as much as possible and cross at 90 degrees if I have to.
"Is it open circuit noise? What if you shorted the input at the end of the cable and see if the noise reduces." Not following here. Short the end that would normally connect to the audio source? Short it to what? Ground on the board?
Thanks,
Some use this... http://www.radioshack.com/radioshack-snap-together-ferrite-choke-core/2730105.html#.VJBYr8t0zcc
aERonAUtical96 wrote:But can a cable introduce noise when it isn't connected on the other end (i.e. no source)? I have a ferrite on the power. I can't put a ferrite on the thicker cable (don't have a ferrite that big). But I can switch audio cables and try it. I think I tried that last year and didn't get better results.
Yes, it can pick up all kinds of stuff. What room is it in and what kind of lighting is in the room? Any fluorescent, CFL stuff? What electronics are near it (computer, etc..)? Sounds like its picking something up from its environment.
On my audio cable, I use a larger core (on both ends) and loop it as many times as I can (3 or 4 i think), like this but a little tighter:

aERonAUtical96 wrote:But can a cable introduce noise when it isn't connected on the other end (i.e. no source)?...
Yes, in the sense that it acts like an antenna.
