Fried Electronics -...
 
Notifications
Clear all

Fried Electronics - why?

17 Posts
8 Users
0 Reactions
5,766 Views
Posts: 106
Topic starter
(@puppycrack)
Estimable Member
Joined: 6 years ago
[#53790]

New to the hobby, and just got 50 12v pixels and a PSU. Bought one of these (pic of PCB below) to test things out and see how bright they would be:

https://www.amazon.com/gp/product/B07FSFXJ1S/

I hooked it up a a Meanwell 12v PSU, connected the pixels to the controller, and everything was fine. So I decided to try power injection. I hooked it like so:


PSU  Controller -- (data / ground) -- pixels
 \                                   /
  \--------- (V+ / ground) ---------/

Notice how the controller in the diagram above is NOT connected to the PSU at all (whoops). I applied power to the PSU, and poof :shock:, smoke from the controller, and now it no longer functions when hooked up the way it was intended. Well, it actually turns all the pixels white, but that's it.

Was the fact that the controller wasn't grounded cause this? Or was this a fault with this cheapy thing and how it's wired? Did I likely damage the pixel string? I did not fuse anything, as I had it on me bench for testing only.

I have a Falcon controller coming in soon, and I want to ensure I understand what happened, so I don't make the same stupid mistake on the real deal - and ensure I follow proper protocol.

Thanks,
- pc

IMG 2631

16 Replies
MartinMueller2003
Posts: 7612
(@martinmueller2003)
Illustrious Member
Joined: 14 years ago

Are you sure that is how it was wired? The controller would have had V- and a dataline which is an output so nothing going back to the controller. Nothing should have gone poof.


Reply
Posts: 13
(@pteller)
Active Member
Joined: 19 years ago

Amazon link says "must use DC5V power supply." Doesn't look like there's a 5V regulator on the board. The Falcon does, so you wouldn't have the same issue.


Reply
Posts: 8517
(@angus40)
Illustrious Member
Joined: 15 years ago
pteller wrote:Amazon link says "must use DC5V power supply." Doesn't look like there's a 5V regulator on the board. The Falcon does, so you wouldn't have the same issue.

This is from the link the OP provided .

Please use the corresponding power supply for the LED strip .

For example :
1.Using DC5V power adapter for this controller when you control DC5V WS2812B LED strip
2.Using DC12V power adapter for this controller when you control DC12V WS2811 LED strip

Please DO NOT use DC12V for this controller when you control DC5V WS2812B LED strip

He should have been fine , but connecting V+ to the controllers gnd cannot be good !


Reply
Posts: 106
Topic starter
(@puppycrack)
Estimable Member
Joined: 6 years ago

As I can now see that my ASCII wiring diagram could be misinterpreted, and I should probably stick with Visio from now on, here is an updated wiring diagram:

diagram

The PSU had AC power applied to it, but the controller had nothing plugged into its DC inputs. It was only connected on its output side. And it *did* work when I had the controller hooked up so it was powering the pixels directly. But as soon as I turned on the PSU in the above wiring - poof and smoke.

I actually bought another one b/c I'm curious to see if I can replicate or if it's a bad one. From what I am gathering, it sounds like this may be indicative of a bad board, but I'll let you know if I fry another one. The main thing I wanted to understand was if I connected a Falcon F16V3 in such a manner that I was injecting power, and the Falcon was connected to strings but not powering them directly, *and* the Falcon was not plugged in or otherwise connected to ground itself, would I fry the Falcon controller? A $10 mistake doesn't bother me too much, but I'd rather not learn a $200 lesson.

Thanks,
- pc


Reply
Page 1 / 4
Share: