I've decided that I'm finally going to add some dedicated circuits for my display. It needs to be done for ease of use as I'm tired of the long extension cord runs in a couple areas to get to the front of the house. I can run the wiring through the garage attic and I have easy access both sides of the wall I want to put the outlets on. I figured I would put a box on the inside wall to bring the circuits to. Then from there drill to the outside and feed the wires out from there.
I'm going to check the local codes to see what I need to do. I know there is an indoor rated wire for attics and I'll use that - read up on it a while back. I watched some videos about running the wire from the inside to out and it says to use an outdoor rated wire. Is that true or could I take the new circuits directly from the circuit box to the outside with the right wire? I'd rather not stop the run if I can help it.
I'll be running (3) 15A circuits replacing what I use now and may add a 4th if the cost isn't too much. I'd rather not do it again anytime soon and that would definitely set me up for the future. I'm well under the 80% rule on the circuits but I like to spread things out.
I'm thinking that's the right track. Run the wires to a box. Then take them outside from there. Is that the proper way to do it? If so is there a recommend junction box for something like this with 4 circuits going to it?
Outside outlets will be GFCI of course. Looking at options for the outside box to see what's out there. Especially for 3 or 4 outlets.
I may try this myself but I do have a couple friends who know well more than I do about electrical work for homes and I'll ask them too. Of course if I even think I'm over my head then I'm calling in the experts and not just my buddies.
Thanks for any advice.
Jason
I would seriously consider running 20A circuits rather than 15A. Or possibly even a sub panel. In my opinion it's better to go over what you think you need and then you have expansion room in the future. This obviously depends on how your panel is currently setup and where everything has to be ran to. If you can post a few pictures of your panel and the layout or positions of where you'd like everything it would help.
StickyWicket wrote:I would seriously consider running 20A circuits rather than 15A. Or possibly even a sub panel. In my opinion it's better to go over what you think you need and then you have expansion room in the future. This obviously depends on how your panel is currently setup and where everything has to be ran to. If you can post a few pictures of your panel and the layout or positions of where you'd like everything it would help.
I'm not sure 20A circuits is the best option. A 15A circuit is good for 1800A fully loaded. that's 5-360W power supplies....of course you should derate a little. If you actually need more power at that location, better to run 14/3+g and have 8-15A circuits. 4-duplex receptacles
mrGrumpy wrote:I'm not sure 20A circuits is the best option. A 15A circuit is good for 1800A fully loaded. that's 5-360W power supplies....of course you should derate a little. If you actually need more power at that location, better to run 14/3+g and have 8-15A circuits. 4-duplex receptacles
I am by no means an electrical guru but in your picture isn't that still only two 15A circuits? Just because there are 4 receptacles doesn't give you more amperage allowed, only more receptacles to plug things into.
Last year I had 12 400 watt power supplies in my show and that is going up this year possibly doubling that amount. You start running out of amps real fast that way.
I have no idea the scale/scope of the OP's display but running circuits again because you didn't plan for future growth is a waste of both time and money.
Funny - I just posted about my project for this as well.
I agree with SitckyWicket - go 20A, not 15A. You get 33% more power, for a very negligible price difference. Make sure you are using 12/3 wire for all you in-wall/in-attic work which can support 20A.
Your setup should be 3 of these:
20A Breaker (in panel) ->to-> 20A GFCI Outlet (I put mine all together in my garage) ->to-> 20A outdoor outlet(s) in your yard.
For my setup, I put out 15A outlets and immediately regretted (which is why I added additional 20A outlets) -- so now it's WAY overkill, but plenty of room to grow. lol
I used these guys under my eaves with a cover:
http://www.homedepot.com/p/1-Gang-Weatherproof-Box-with-Three-1-2-in-Outlets-5320-0B/204208007?MERCH=REC-_-rv_search_plp_rr-_-NA-_-204208007-_-N
That way I only had to drill a hole into the attic, and mount the box over the hole (back-fed). Easy to do, and looks very clean.
