xLights Sequence Pa...
 
Notifications
Clear all

xLights Sequence Pauses every few seconds

6 Posts
2 Users
0 Reactions
2,679 Views
Posts: 92
Topic starter
(@curtinti)
Estimable Member
Joined: 7 years ago
[#53291]

Hi all,
Finally started to put everything together and ran into an issue I was not anticipating after testing in my basement. My set up is a Falcon 16v3 with a differential to 4 receivers. Once I got a good amount set up including the megatree I turned on a few sequences once it got dark to see how it looks. What I found was that every 10-20 seconds the sequence pauses/stops and then picks up where it left off. What would cause this issue? I've included a video. At the start the sequence is stopped but picks back up and then stops again. Any advice would be great. If there is other info/data you need let me know. I'm stumped on this one.

Thanks,
Tim


5 Replies
Posts: 120
(@superdave)
Estimable Member
Joined: 13 years ago

Any wireless involved?

Is xLights open when this is happening?


Reply
Posts: 92
Topic starter
(@curtinti)
Estimable Member
Joined: 7 years ago
superdave wrote:Any wireless involved?

Is xLights open when this is happening?

No wireless ... I have Fios Gigabit bandwidth so I imagine I have enough bandwidth. Hardwired from the router to the Falcon and then again ethernet to the 4 receivers.

Yes, xLights was open while I was testing.

Tim


Reply
Posts: 92
Topic starter
(@curtinti)
Estimable Member
Joined: 7 years ago

I think I may have figured this out. I was working off a static ip address (192.168.1.30) on my home network for my falcon controller so I am guessing that was the issue. I had an extra switch laying around so I configured a separate network and gave the Falcon a new ip address of 192.168.10.10. I then set an extra laptop up with a static ip address on the same network and connected it to the same switch. It's working as expected in my basement. We will see what happens tomorrow outside. Do you think that was the issue?

Also, I have been keeping my sequences on OneDrive so I could sync to a separate laptop and work on them there. I assume that isn't a problem since the files are synced locally to the laptop, right?

Tim


Reply
Posts: 120
(@superdave)
Estimable Member
Joined: 13 years ago

It could be a variety of things.

-Perhaps there was something on your prior network, that was doing periodic broadcasts on the network and clogging things up briefly. Lots of home network stuff can cause those problems. Having a separate network is definitely a common thing people do, but often isn't needed. However, it can be easier to troubleshooting than trying to narrow down what is happening on your home network.

-I wouldn't expect OneDrive to be the problem, but it is possible it was hogging network resources or other resources on your computer during the show. Having something dedicated with NOTHING else running is certainly ideal. This is one of the advantages of having a Pi running FPP.

I'm glad you got things sorted. Probably worth investigating more in the off-season 🙂


Reply
Posts: 92
Topic starter
(@curtinti)
Estimable Member
Joined: 7 years ago
superdave wrote:It could be a variety of things.

-Perhaps there was something on your prior network, that was doing periodic broadcasts on the network and clogging things up briefly. Lots of home network stuff can cause those problems. Having a separate network is definitely a common thing people do, but often isn't needed. However, it can be easier to troubleshooting than trying to narrow down what is happening on your home network.

-I wouldn't expect OneDrive to be the problem, but it is possible it was hogging network resources or other resources on your computer during the show. Having something dedicated with NOTHING else running is certainly ideal. This is one of the advantages of having a Pi running FPP.

I'm glad you got things sorted. Probably worth investigating more in the off-season 🙂

So everything worked last night inside but then i took it back out and same thing happened. Brought it back in and tried everything... reset Falcon, changed IP. Wouldn’t work. Then for some reason i just connect a cable directly to the port on the Falcon and it started to work. Seems as though the short 6 in ethernet cable to goes to the ethernet gland to the controller was bad. Changed that out and back in business.

But now i have it back on my home network instead of a separate network. But it seems to be fine. From my verizon fios router to a netgear switch and out of the switch i just have a line going to the controller and a laptop which will be dedicated to running the show. It is running in unicast. If that is the setup do i need to create a separate show network or so long as the laptop and controller are the only devices coming out of the switch I’m good?

Tim

Sent from my iPhone using Tapatalk


Reply
Share: