WS2812B capacitor
 
Notifications
Clear all

WS2812B capacitor

12 Posts
7 Users
0 Reactions
7,598 Views
Posts: 295
Topic starter
(@daytimer)
Reputable Member
Joined: 15 years ago
[#33002]

I have the SMD WS2812B's from Ray Wu. I managed to tear off part of a trace for a data out line. Of course, I didn't order any extras! I was able to find a schematic for the WS2812B's at http://www.adafruit.com/datasheets/WS2812B.pdf , but I still don't know where the capacitor falls inline on the pixel. I am just going to pick off the data out of the pixel, but don't want to bypass the cap if it is in that line.


11 Replies
Posts: 2128
(@livermore-dad)
Famed Member
Joined: 16 years ago

Shit have a few here that i snipped off, could send in an envelope.Not sure what is buste don them, but maybe just maybe you can scavange the part off. But you can't just cut that one off and move on?


Reply
Posts: 853
(@roterhead)
Prominent Member
Joined: 15 years ago

That's going to be hard to fix. Easiest way is to remove that pixel and add in another...


Reply
Posts: 295
Topic starter
(@daytimer)
Reputable Member
Joined: 15 years ago

The busted part is the data out trace on the end. I just don't know if that cap is in the data line or not. If not, I was just going to go directly to the out pin on the pixel.
These strings are part of window frames I have set up for 6 Windows in the porch. Removing one would make it goofy to program, especially since that broken trace is not at the end of that frame. I need the data out from that one to go to the next vertical string on the same window.


Reply
jklingert
Posts: 1767
(@jklingert)
Noble Member
Joined: 16 years ago

I doubt the capacitor is connected to the data line, most likely connected to the V+ and GND. Look at the datasheet http://doityourselfchristmas.com/forums/attachment.php?attachmentid=17633&d=1357958385


Reply
Posts: 2128
(@livermore-dad)
Famed Member
Joined: 16 years ago
daytimer wrote:The busted part is the data out trace on the end. I just don't know if that cap is in the data line or not. If not, I was just going to go directly to the out pin on the pixel.
These strings are part of window frames I have set up for 6 Windows in the porch. Removing one would make it goofy to program, especially since that broken trace is not at the end of that frame. I need the data out from that one to go to the next vertical string on the same window.

Looking at the back of mine, it seems to be inline of the data (working on a picture but it's tough)

The cap is to the right of that lil dot, the dot is the LED

Tory


Reply
jklingert
Posts: 1767
(@jklingert)
Noble Member
Joined: 16 years ago

A capacitor is usually added across a V+ and GND to filter out power transients and noise. It would make no sense in a data line where it would affect the shape and timing of the data signal. Look at the last picture in the datasheet.


Reply
Posts: 2128
(@livermore-dad)
Famed Member
Joined: 16 years ago
jklingert wrote:A capacitor is usually added across a V+ and GND to filter out power transients and noise. It would make no sense in a data line where it would affect the shape and timing of the data signal. Look at the last picture in the datasheet.

Nope you are right, sorry, old eyes and not looking at it long enough.. My guess is the cap straddles the data line and the postive/negative copper is on either side of that strip, where the capacitor is. So I believe it would be safe to take the data straight from the pixel.. Sorry took some more time looking at it.

Tory


Reply
RobG
Posts: 1255
 RobG
(@robg)
Noble Member
Joined: 14 years ago

The caps are not inline, they are bypass caps.
If there's some part inline, it's a resistor. They started adding one at the beginning of each 0.5m strip section when WS2812B were released.
In your case, looks like you only have a capacitor.


Reply
Posts: 6
(@camper)
Active Member
Joined: 13 years ago

Get a sharp stanley knife and carefully scrape off the solder mask underneath the letters DO, there is a perfectly good copper trace there you can make a new pad out of


Reply
Page 1 / 2
Share: