BTW, we're these strings or strips?
These are strings.
thebaronn wrote:......but I was recently sucked into the DIY pixels from Ray Wu after my great LOR CCPixel debacle........
Thank you for your input.
Eric
I have to ask. What is the "my great LOR CCPixel debacle"
It has been a while since I have been on this forum (mostly because there are smarter and more qualified people already answering questions)
So the Nerds could not answer your questions and you come to us Dweebs instead?
Did we at least answer more questions than the Nerds?
It's important to our psyche that we finally defeat those Nerds.... :pragnie:
Aurbo99 wrote:So the Nerds could not answer your questions and you come to us Dweebs instead?
Did we at least answer more questions than the Nerds?
It's important to our psyche that we finally defeat those Nerds.... :pragnie:
I have mostly just been leeching off of the forum. Anything I think of will be old hat for all of you.
Macrosill wrote:I have to ask. What is the "my great LOR CCPixel debacle"
Well, it's a long story and I know you want to read about it......
I barely have time for my hobby and my "following directions" and "nice clean soldering" genes are not present so I like the plug and play stuff. If my setup takes 80 hours, but 79 of those hours are troubleshooting my mistakes, it's not worth my time. So I bought a chunk of those plug and play CCPixels from LOR.....
http://forums.lightorama.com/index.php?/topic/20956-ccp-santa-house/ (my PC version, didn't want to get banned)
http://www.lightshowpro.com/lightshow-support/2583-lightshow-pro-work-ccpixel-santa-house.html
Me an Dan emailed several times.....said he would look over my sequences......then siad I was expection too much from their product....and then, he eventually never responded anymore and well, I didn't care. after 2 people over at LSP showed me they could recreate what I wanted to do overnight and it worked, I was sold.
I sold most of them. I kept a few because I liked the idea of a enclosed pixel solution (I used them in my Halloween tree and my "Blast from the Past" mega tree)
I got home from work at 6am tuesday morning. I did one firmware update and then went to sleep. When I was leaving the house later with my wife she said: hey your sh*$ is working.....well that side. (She is not a huge fan of my hobby) So it looks like the firmware was the issue. I just did the other 4 boards and hope they look good tomorrow.
So my next question, why were only some pixels affected in this weird way?
Thank you all again for your help.
Eric
well i think they had the batchs mixed up so you got some of the old IC and come new. but im glad the firmware is working for you. dont worry my wife isnt a fan most of the time either b/c of the time lol. but she still helps here and there.
thebaronn wrote:I got home from work at 6am tuesday morning. I did one firmware update and then went to sleep. When I was leaving the house later with my wife she said: hey your sh*$ is working.....well that side. (She is not a huge fan of my hobby) So it looks like the firmware was the issue. I just did the other 4 boards and hope they look good tomorrow.So my next question, why were only some pixels affected in this weird way?
Thank you all again for your help.
Eric
The 2811 pixels look for a gap in the data to mark the end of a data frame, and when they see that gap they load their last received data bits into the leds and go into a 'wait for start of data' mode. The data sheet says this gap has to be 50us or longer. The 1804s (which the 2811s are clones of), actually recognized anything longer than 10us as end of frame. Tthe 2811s recognize a much smaller gap as end-of-frame, more like 5-6 us instead of 10 or 50. It turns out that the time the E68x controllers take to process the data in betwen pixels was right around 6us. This was more than enough safety margin for the 1804s, but a 2811 that is just a bit off on its timing will think that the data frame was finished before it actually was.
The firmware update reduces the size of the data gap between pixels.
thebaronn wrote:I got home from work at 6am tuesday morning. I did one firmware update and then went to sleep. When I was leaving the house later with my wife she said: hey your sh*$ is working.....well that side. (She is not a huge fan of my hobby)
Eric
Ah, if she was paying attention enough to notice it was working, there is hope for you to bring her to the dark side :devilred: Bwhahahahah :devilred:
