Our Pixel Snowmen!
 
Notifications
Clear all

Our Pixel Snowmen!

46 Posts
20 Users
0 Reactions
19.3 K Views
Posts: 214
Topic starter
(@gary-martin)
Estimable Member
Joined: 18 years ago
[#22953]

New for this year I fabricated up some snowmen made out of acryllic circles with TLS3001 pixel strips mounted on the edges aimed inward. The acryllic was frosted and flame polished on the edges only for good light transference. 3/4" vinyl tubing was cut lengthwise to make the protective cover over the strips. I used 1" dia acrylic rod, cut into 2" lengths for the spacers to hold it off of the angle steel back frame. Sandevices E681 controllers for interface and 134 pixels on each snowman.

I haven't had a lot of time yet to create effects but some of the early stuff has turned out pretty nice:

(second half below)


45 Replies
Posts: 368
(@henkvis)
Honorable Member
Joined: 18 years ago

Nice! Pictures and WoW please ? :freak:


Reply
Posts: 60
(@rlw162)
Trusted Member
Joined: 18 years ago

Gary, this is a really cool effect! Do you have any pictures of the snowmen? What was the thickness of the acrylic circles you used?


Reply
lightman
Posts: 1524
(@lightman)
Noble Member
Joined: 19 years ago

Terrifc job! I especially like the snowman that are your lead effect. You sequenced them very effectively with the audio....kept my attention.

You have also used the "dripping lights" or "meteor lights" very effectively. Your application makes me start to think about my trees in front.

Congrats....
Lightman


Reply
komby
Posts: 871
(@komby)
Prominent Member
Joined: 14 years ago

Awesome! Snowmen and the poles/arches were so captivating I almost didn't notice the HUGE mega tree ;).


Reply
Posts: 214
Topic starter
(@gary-martin)
Estimable Member
Joined: 18 years ago

Still pics of the Snowmen:

http://www.flickr.com/photos/perryddock/8256433512/in/set-72157631336988114/lightbox/

http://www.flickr.com/photos/perryddock/8256432594/in/set-72157631336988114/lightbox/

http://www.flickr.com/photos/perryddock/8256426554/in/set-72157631336988114/lightbox/

The acrylic I used is the 1/4" stuff, sheet stock and then cut my own circles on a bandsaw with a circle jig. The spine is 1" angle steel, cut and welded in my shop with 18" worth of ground anchor to drive them in with. The hats are just more of the same acrylic with 6" sched 40 PVC to make the cylinders. Mighty Mini RGB flood inside the hats.

Oh, before anyone asks, we're still going to add buttons, eyes, mouth, etc with black adhesive vinyl circles we have. 😉 It's just been below freezing the last few days since the last one was finished and haven't had a chance to put the finishing touches on them yet. 😉

I've attached a .PDF of the snowmen design. Fixture on the right is the spine frame.


Reply
Posts: 368
(@henkvis)
Honorable Member
Joined: 18 years ago

Great ! Nice pictures and description.

How did you arrange / setup you controller? I mean pixel wise, you should assign the same length to each output or not?

You have 16 outputs on a E681, and normally that one can only drive 4 universes.

How?


Reply
Posts: 214
Topic starter
(@gary-martin)
Estimable Member
Joined: 18 years ago
henkvis wrote:Great ! Nice pictures and description.

How did you arrange / setup you controller? I mean pixel wise, you should assign the same length to each output or not?

You have 16 outputs on a E681, and normally that one can only drive 4 universes.

How?

Yeah, I just used two E681s, one snowman per cluster on them. With the upgrade kit I could have shoved 6 onto a single interface but then that wouldn't have helped much. 😉 One large concern I had was to get maximum speed out of these strings and that's why I did 4 strings of 134 pixels per controller. Check the start of the video below, you'll see how fast I'm pushing these strings and it performed flawlessly.


Reply
Posts: 339
(@heldwhat-christmas)
Reputable Member
Joined: 15 years ago

Love the snowmen! My wife has a healthy obsession with snowmen (we have a room in the house dedicated to Snowmen from Thanksgiving through March) so I'm looking at building a variant of these...
This will be my first attempt at pixels so I have a basic newbie question here.... I thought you were using smart pixels which are controlled individually so I don't understand why you had to cut your strips in to 6 segments per circle... As I was working up my design I thought it would just be 1 continuous strip for each circle...
Great job on these!


Reply
Posts: 368
(@henkvis)
Honorable Member
Joined: 18 years ago
Heldwhat Christmas wrote:Love the snowmen! My wife has a healthy obsession with snowmen (we have a room in the house dedicated to Snowmen from Thanksgiving through March) so I'm looking at building a variant of these...
This will be my first attempt at pixels so I have a basic newbie question here.... I thought you were using smart pixels which are controlled individually so I don't understand why you had to cut your strips in to 6 segments per circle... As I was working up my design I thought it would just be 1 continuous strip for each circle...
Great job on these!

I think Gary also used full strips for the circles. He just creates some great effects in such a way that you would think that there are segments.....


Reply
Page 1 / 5
Share: