WS2811 pixel compat...
 
Notifications
Clear all

WS2811 pixel compatibility

26 Posts
9 Users
0 Reactions
65.4 K Views
timon
Posts: 2149
(@timon)
Noble Member
Joined: 16 years ago

Well I don't think I've seen a lower price for pixels as this:

http://www.aliexpress.com/fm-store/701799/209889132-563831930/RGB-full-LED-pixel-module-WS-2811IC-DC5V-input-50pcs-a-string-IP68.html

Now that we can drive the WS2811 IC this and other WS2811 pixels may be the way to go unless you need the 12 bit option that the TLS3001 gives.


Reply
Posts: 290
(@fasteddy)
Reputable Member
Joined: 17 years ago
jstjohnz wrote:I finally got around to testing "real" WS2811s. The issue was timing. When setting up for the original 1804 pixels, I found 3 different data sheets with 3 different timing specs, so what I did was find the range where they worked, and set the final timing in the middle of that range. It turns out that that particular timing is just a hair off for the WS2811s.

So now the WS2811s are working, they will be setup as 1804s, I just need to verify that the 1804s still work properly, and of course I can't find my string of 1804s to test that...

Jim how did you go in the end with the 2811, you state that you got this running using the 1804 protocol, im wondering if you came across any issues as there are some slight timing differences in the data sheet.

The 2811 series offers great value to the community with crazy prices like a 5 metre strip with 30 LED and 10 IC per metre at $36, the whole range of the 2811 is much cheaper than anything else out there and with so many with tight budgets this is a very important IC to support as it then offers far better value for any controller supporting it.


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Jim,
Your set up will need a slow and a Fast option. Slow operates NRZ @ 400KHz, while fast operates NRZ @ 800KHz.

Whilst the option exists on the IC Data sheet, I haven't seen the rate dedatiled on any product sheets.


Reply
Posts: 1249
Topic starter
(@jstjohnz)
Noble Member
Joined: 17 years ago
fasteddy wrote:Jim how did you go in the end with the 2811, you state that you got this running using the 1804 protocol, im wondering if you came across any issues as there are some slight timing differences in the data sheet.

The 2811 series offers great value to the community with crazy prices like a 5 metre strip with 30 LED and 10 IC per metre at $36, the whole range of the 2811 is much cheaper than anything else out there and with so many with tight budgets this is a very important IC to support as it then offers far better value for any controller supporting it.

There was a lot of confusion regarding the timing of the 1804s, with several different data sheets giving different numbers. The 1804s worked over a range of about 600kbps to about 850kbps. I picked a value near the middle of this range, I think about 700kbps. As it turns out, this is just a hair too slow for the WS2811s. So now my timing is set right at 800kbps, and that value works for the WS2811s and the 1804s.

Has anyone come across any of these pixels that are configured for the 'slow' mode?


Reply
Matt_Edwards
Posts: 2664
(@matt-edwards)
Famed Member
Joined: 18 years ago

Jin are you implementing a NRZ protocol as per the data sheet or the Pseudo NRZ as per Tabor testing over at ACL?

Tabor suggests
1 ____
1 => _2 3 4 5 Ie 4 out of 5 bits are high

_ 2 3 4 5
0 =>1 _____ Ie 4 out of 5 bits are low


Reply
Page 2 / 6
Share: