WS2811 12v bullets ...
 
Notifications
Clear all

WS2811 12v bullets power usage

17 Posts
7 Users
0 Reactions
12.9 K Views
Posts: 3
Topic starter
(@woodstock-ontario)
Active Member
Joined: 9 years ago
[#46328]

im sure this has already been asked but i cant seem to find it just need a bit of info on power supply requirements for a mega tree i will be building

i will have a 32 strand tree with 150 pixels per strand. i have the power supply for the controller but will be using other supplies to power the strings i have bought pixels from 2 different suppliers and have noticed that if i use one suppliers string of 50 pixels at the start of the power i can actually get all 150 powered(100 from supplier b) with little to no difference in full white from start of the strands and the end.

my question is i have the 350 watt 29 amp power supplies from holiday coro how many would i need to power this tree 50 pixels per string x 3 strings per line x 32 lines = 4800 pixels
just need to see how many supplies will be needed to power this tree up to full white

i am very new to pixels and excited to see what i can do this year


16 Replies
Posts: 116
(@studiopro)
Estimable Member
Joined: 12 years ago

Will you be running the pixels at full power? For my pixels that are NOT the C9 style, or inside a display element I run them at 40%, which will obviously change your power need dramatically. In my small testing of some strings I was getting around .056 amps per pixel full and at 40% brightness around .023. This varied in a 100 pixel string vs a 50 pixel string with voltage dropping a bit. You can plan for .06 amps per pixel to plan it out on 100% brightness to be safe. In my opinion it's best to have overhead in the power supply to give it a nice long life.


Reply
Posts: 299
(@dcamron)
Reputable Member
Joined: 10 years ago

Don't recommend Holiday Coro PSU's. Same thing you can get direct from China at a cheaper price. I've had 2 of those fail and output more than 18V. Blew out 800 pixels. Holiday Coro likes to use the brand name "Mean well" on their website but what they sent me was not a Mean Well. I recommend you buy the real thing from a trusted vendor who's sold hundreds, if not thousands of them.

A 348W PSU outputting 12V will give 29A. The most known measure of current per pixel is .06A at 100% full white. That's .3W per pixel. Given this, a 348W PSU at 12V should support up to 483 pixels. If you load the PSU at 80% then you're down to 386 pixels. As someone else mentioned, running your pixels at 40% or 50% brightness will reduce your requirement significantly. You may get away with 4 or 5 PSU's. I don't know of any value curves for various levels of brightness so can't calculate that.


Reply
Posts: 672
(@pixelpuppy)
Honorable Member
Joined: 12 years ago

Total current draw in pixel strings is not a linear calculation. Yes, a single pixel draws .06A at full white, but a string of 100 pixels does not draw 100 times that. Its not linear due to resistance in the wire. You'll get more realistic totals if you measure the current draw on one of your strings and then multiply by the number of strings instead. And yes, its highly recommended to set your controller to 80% maximum brightness (or less). There is not much need to run 100% brightness at nighttime and many people are fine setting it to 50%. 100% brightness is what they use on Las Vegas billboards to see them in broad daylight. :cool2:


Reply
Posts: 3
Topic starter
(@woodstock-ontario)
Active Member
Joined: 9 years ago

Thanks for all the info I do have 11 power supplies but I will look at reducing the pixels to lower percentages to reduce power needs I don't want to blind or tan people so I will have to see what works


Reply
Page 1 / 4
Share: