Wireless DMX RGB Co...
 
Notifications
Clear all

Wireless DMX RGB Controller

12 Posts
6 Users
0 Reactions
3,951 Views
michaelc
Posts: 1540
Topic starter
(@michaelc)
Noble Member
Joined: 19 years ago
[#36075]

I'd like to file this under wish list.

Ideally I would like to use the new 10W RGB Flood boards as follows:
1) Re-Use the original AC-DC transformer to drive the board
2) add a second small board inside the housing similar to the ren4flood but smaller and only 3 channels
3) Connect the 3 channel controller to one of these: http://www.ebay.com/itm/281446710640?_trksid=p2060778.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT

This would give me a line voltage, Wireless DMX RGB Flood light.

Questions:
1) Has anyone tried re-using the original transformers for such a purpose
2) Is there a 3 channel board similar to the Ren4Flood that can convert the DMX signal to RGB?
3) Am I nuts? (Rhetorical Question)


11 Replies
Xenia
Posts: 1358
(@xenia)
Noble Member
Joined: 15 years ago

Well if we creating a wish list, I would like to see DMX in and out for daisy chaining like the TIR Destiny Floods, maybe with power injection every so many floods possibly using the on board transformer or other power supply as needed. The driver board that RobG created fits under the lens of the flood enclosure most of us are using. There s a secondary power box on these flood enclosures that could be used for a second board.


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago

Your basically describing the rf1 stuff.

http://www.komby.com/rf1_12
http://www.komby.com/rf1-dumb-rgb-expansion-board-rev2-board-bom

What kind of transformer are you talking about here?

Assuming normal led floods:
One of thous $2 dc to dc buck supplies to bring the voltage down from the flod supply most are around the 24v mark.


Reply
Posts: 37
(@youngberg1950)
Eminent Member
Joined: 14 years ago

I'm playing with the idea of using a Komby RF_1_12 for the wireless part. I'm going to test using the RF_in_RGB_out but not use his RGB shield. I'll just use the pins off the atmega to controll RobG's flood board. I'm going to just feed it 12V and not use the built in Constant Current Driver. It looks like the board you linked to just outputs DMX so you will need something in between it and the 10W RGB Flood board.

Doug


Reply
michaelc
Posts: 1540
Topic starter
(@michaelc)
Noble Member
Joined: 19 years ago
youngberg1950 wrote:I'm playing with the idea of using a Komby RF_1_12 for the wireless part. I'm going to test using the RF_in_RGB_out but not use his RGB shield. I'll just use the pins off the atmega to controll RobG's flood board. I'm going to just feed it 12V and not use the built in Constant Current Driver. It looks like the board you linked to just outputs DMX so you will need something in between it and the 10W RGB Flood board.

Doug

Exactly that is why I mentioned the REN4Flood. A Ren3Flood would be ideal. The Komby gear could be made to work as well.

As to the pucks, the enclosures most of us bought came with either a warm white or bright white led wired to a transformer. I'll have to put my meter on it and see what the voltage is, but if we can just connect to standard 110Voltage AC, I can reduce my need for 5V and 12V power supplies littering my yard. The output can drive whatever boards we put into the housing. With the 10W Driver board mounted under the reflector, there is PLENTY of room on the other side of the reflector for another little board, the back power compartment would be re-used for the stock transformer so you probably wouldn't want to squeeze any other boards in there.


Reply
michaelc
Posts: 1540
Topic starter
(@michaelc)
Noble Member
Joined: 19 years ago

With the komby gear you would need to use the external antenna since we are inside a metal housing.


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago
Reply
Posts: 37
(@youngberg1950)
Eminent Member
Joined: 14 years ago

Yep I overlooked the Ren4Flood piece..... My Bad!

I also bought the 120V AC warm white floods with the "transformer" in the back. The problem is that it is designed to provide Constant Current of 300 to 1000ma depending on what LED Chip is in the flood. I don't believe that you can just connect a logic based circuit to it and expect the 3/5V that is needed. Maybe one of the more experienced guys can confirm or deny this???

If I go the RF_1 route then I will just put it in an external PVC "pill case".

Doug


Reply
kingofkya
Posts: 2165
(@kingofkya)
Noble Member
Joined: 15 years ago
youngberg1950 wrote:Yep I overlooked the Ren4Flood piece..... My Bad!

I also bought the 120V AC warm white floods with the "transformer" in the back. The problem is that it is designed to provide Constant Current of 300 to 1000ma depending on what LED Chip is in the flood. I don't believe that you can just connect a logic based circuit to it and expect the 3/5V that is needed. Maybe one of the more experienced guys can confirm or deny this???

If I go the RF_1 route then I will just put it in an external PVC "pill case".

Doug

Most are around 24 volts then they very the voltage to mantain current. So with a supply that can handle voltage varation is all you would need. For example:
http://www.ebay.com/itm/DC-DC-Boost-Buck-adjustable-step-down-Up-Converter-XL6009-Module-Solar-Voltage-/400597430280?pt=LH_DefaultDomain_0&hash=item5d4577b008

However i would take great care some may or may not be an isolated supply, so no PC connection(serial usb etc), scope or grounded equipment, until proven otherwise.


Reply
michaelc
Posts: 1540
Topic starter
(@michaelc)
Noble Member
Joined: 19 years ago

IN this use I would see it something like, AC power to transformer, Transformer to either RF1 or some version of REN, RF1 or REN to the 10W LED driver board,


Reply
Page 1 / 2
Share: