You are correct on the rating for CL2 and CL3. You want to definitely check on those with speaker wire, thermostat wire, and other of the so called "low voltage" wires that are out there as they may not be rated for what you want as they are usually not considered as "voltage carrying" types of wire.
Also using wire having a UV rating is a good thing to consider as well as the jacket on non UV rated stuff will degrade in sunlight and start to break down. A good UV rating will make the wire hold up better for a longer time although any wire laying out in the weather can get damaged by weather, animals, kids, ice, snow, etc..
With pixels you are going to find that the number of pixels is the driving factor in the wire size you are going to need for any one display item. A string of 50 pixels requires less power than a string of 200 obviously so it becomes a matter of how many pixels you are trying to "drive" at a certain location.
Once you know what pixels you are going to use, you can get the wattage of each pixel (use the full on value of white - ie. max draw) to calculate how much power you are going to need at that point. Then you can get an idea of what wire to use.
Most are finding that using more smaller power supplies spread around gives better flexibility although using larger power supplies with buck down converters will also work with less supplies as you can run higher voltage "mains" out to areas and then reduce down for different parts.
You don't say if you are using 12 volt pixels or 5 volt ones? That can also effect your power setup a lot. The 5 volt is more efficient for power usage but will require larger wire sizes to reduce the drop in voltage while 12 volt can get along with smaller wire sizes. Also 5 volt pixels will "usually" go for 50 nodes before having to have power injection while the 12 volt ones can go 100 nodes before requiring it.
Using 14/4 may be overkill for a lot of your distances but without knowing exactly what pixels and how things are going to be laid out it is not a certainty to say. You really only need two wires for power as your data lines can easily run a long distance on plain old Cat5 cable although I understand you are trying to use one cable for the run. You can also look at some types of cable that use a twisted pair of 22 awg wire and a couple of large awg wires in one cable to make things work. Again it depends on whether you are using 3 wire or 4 wire pixels?
It is a balancing act of sorts to figure it all out but you are on the right track and I so agree with you on "Better to measure twice and cut once" !
It helps if you put where you are located in your profile so that people can see it when they look at posts. That gives a better overall idea of how to deal with your requirements for things and you may find someone who lives "down the street" from you that can help.
beeiilll wrote:You are correct on the rating for CL2 and CL3. You want to definitely check on those with speaker wire, thermostat wire, and other of the so called "low voltage" wires that are out there as they may not be rated for what you want as they are usually not considered as "voltage carrying" types of wire.Also using wire having a UV rating is a good thing to consider as well as the jacket on non UV rated stuff will degrade in sunlight and start to break down. A good UV rating will make the wire hold up better for a longer time although any wire laying out in the weather can get damaged by weather, animals, kids, ice, snow, etc..
With pixels you are going to find that the number of pixels is the driving factor in the wire size you are going to need for any one display item. A string of 50 pixels requires less power than a string of 200 obviously so it becomes a matter of how many pixels you are trying to "drive" at a certain location.
Once you know what pixels you are going to use, you can get the wattage of each pixel (use the full on value of white - ie. max draw) to calculate how much power you are going to need at that point. Then you can get an idea of what wire to use.
Most are finding that using more smaller power supplies spread around gives better flexibility although using larger power supplies with buck down converters will also work with less supplies as you can run higher voltage "mains" out to areas and then reduce down for different parts.
You don't say if you are using 12 volt pixels or 5 volt ones? That can also effect your power setup a lot. The 5 volt is more efficient for power usage but will require larger wire sizes to reduce the drop in voltage while 12 volt can get along with smaller wire sizes. Also 5 volt pixels will "usually" go for 50 nodes before having to have power injection while the 12 volt ones can go 100 nodes before requiring it.
Using 14/4 may be overkill for a lot of your distances but without knowing exactly what pixels and how things are going to be laid out it is not a certainty to say. You really only need two wires for power as your data lines can easily run a long distance on plain old Cat5 cable although I understand you are trying to use one cable for the run. You can also look at some types of cable that use a twisted pair of 22 awg wire and a couple of large awg wires in one cable to make things work. Again it depends on whether you are using 3 wire or 4 wire pixels?
It is a balancing act of sorts to figure it all out but you are on the right track and I so agree with you on "Better to measure twice and cut once" !It helps if you put where you are located in your profile so that people can see it when they look at posts. That gives a better overall idea of how to deal with your requirements for things and you may find someone who lives "down the street" from you that can help.
I am planning on using WS2811 12 volt pixels 50 per string from DIYLEDExpress.com for all my pixel needs.
I rather buy a cable that's to big and play it safe. Like I said I want to do this once not redo it every year or so. The UV point is a good one because I live in deep south Texas. Like 20 minutes from Mexico it is hot and sunny 364 days of the year. I have yet to see anyone in my neck of the woods on any of these forums.
I plan on using either a e682 or PixLte 16 for the mega tree and one of those for the 10 mini trees and 4 leaping arches. The mini tress will be 1 string of 100 pixels each for 10 mini trees, the leaping arches will be the WS2811 12 volt 60 leds per meter strips. The mega tree will be 12 strings of 100 pixels, folded over to make total of 24 strands 50 pixels each. Each string will be attached to its own controller output so I think I am ok not having to power inject since I will keep all 100 pixels on each string max.
I hope I have not confused you with my terminology, not all the way there yet with the lingo...yet.
P.S.
I know the WS2811 12 v is a 3 strand but I was going to run two positives on each run.
HA, no problem with the lingo! I know what you mean as everybody can have just a little bit different interpretation of what things can mean so it can become confusing at times.
I agree with the do it once as well. I too tend to over build things but I have rarely every had to go bad and redo stuff! I like overkill!!
Your 14/4 then "should" be plenty big enough for things. Once you know where things are going to be and the power requirements for it all, you may find that even an 18awg cable will be large enough for each run of power to strings! I would say that the majority of people are using 18/4 stranded security cable for most of their displays as it is big enough and has plenty of capacity to handle the power required for a section of string even when used with a "power bus" setup style of structure in a display!
The only problem you may incur with the 14/4 could be making the attachment of it to the pixel strings as soldering that size wire can be tough onto the leads but certainly not impossible. I see that the strings on Todds site (DIYLedExpress) use 18 awg leads so that should work okay although I would say you will want to think about using some form of connectors to mate things together and make setup and tear down easier for you. Also the connectors you use may dictate how much power you are able to push through things as well.
I have not used the SansDevice or PixLite controllers so can't be much help there but there are many who have so they can assist where necessary. You are certainly on the right track with it though!
beeiilll wrote:HA, no problem with the lingo! I know what you mean as everybody can have just a little bit different interpretation of what things can mean so it can become confusing at times.I agree with the do it once as well. I too tend to over build things but I have rarely every had to go bad and redo stuff! I like overkill!!
Your 14/4 then "should" be plenty big enough for things. Once you know where things are going to be and the power requirements for it all, you may find that even an 18awg cable will be large enough for each run of power to strings! I would say that the majority of people are using 18/4 stranded security cable for most of their displays as it is big enough and has plenty of capacity to handle the power required for a section of string even when used with a "power bus" setup style of structure in a display!
The only problem you may incur with the 14/4 could be making the attachment of it to the pixel strings as soldering that size wire can be tough onto the leads but certainly not impossible. I see that the strings on Todds site (DIYLedExpress) use 18 awg leads so that should work okay although I would say you will want to think about using some form of connectors to mate things together and make setup and tear down easier for you. Also the connectors you use may dictate how much power you are able to push through things as well.
I have not used the SansDevice or PixLite controllers so can't be much help there but there are many who have so they can assist where necessary. You are certainly on the right track with it though!
Ya no kidding with the overkill, better safe than sorry my wife gets annoyed by my over preparedness with the reading and researching then the over doing it. But when I do something I only do it once the right way. Yeah I plan on buying the 25 pack of water proof connectors from DIYLEDExpress.
