jchuchla wrote:I agree here. I thought I left enough uncertainty in my original comment here to indicate I was just offering a reasoned guess on the side of safety. But I can also easily see how I may have sounded authoritative.To be clear, I am not an authority on this subject.
That's why I opened with: "One can spend a lifetime just studying ground wiring..." :).
Most people don't understand it. I have a minor in electrical engineering, and I don't understand it. The electrician who recently replaced all the wiring in my house definitely doesn't understands it.
There is a good thing there is code, because if it was up to people to make decisions on a case-by-case basis on how to keep things safe, a lot of us would be dead by now!
I hope nobody use this thread to make an authoritative decision one way or another. Except for one thing - PLEASE don't take the E682 manual literally and wire up V- to an open Ground connector on the power supply. If you DO want to bridge V- (or V+) to ground, make sure you are actually running a wire from there to earth ground. Otherwise you're definitely making things worse.
120V DC and 120V AC..are VERY different when it comes to contact with human skin, are they not? I can show you a video of a guy holding the clamps of 120V DC 500A
My turn... In my first post on this subject I was being serious for the first paragraph and poking a little bit of fun in the second.. (obviously :razz:)
There are several reasons to ground or not to ground. Troubleshooting grounding issue and ground loops is often a "black art" and experience is one of the best teachers we have. Let me bring up some technical points and this is regarding our hobby and LV supplies that are 5vdc or 12vdc. (this is informational only and not to be taken as a substitute for required practices)
1. A DC power supply is not a part called a "transformer". Most supplies have transformers but they are not correctly called that as a whole.
2. Not all DC supplies are isolated from the main input supply. (Be very careful of these)
3. Not all manufacturers allow for physical grounding of the secondary. (Be very careful of this issue)
4. In our hobby, most supplies are electrically isolated from input to output side, however, some of the lower cost supplies can inject switching noise due to inadequate design. Grounding the input, which is in essence grounding the chassis can help squelch that noise and keep it from radiating. Always use the earth ground for the input supply. (120vac in most cases).
5. Grounding of the V- on the output side of something that produces audio or data streams, (1Mhz or below) is to make a common point of reference for noise and spurious signal "grounding". In theory this works pretty well but not always. Due to layout of your pixels and wiring this may actually not be practical and may even cause ground loop issues which could be worse and not better. Other equipment on your system, even if unrelated to your display, can also cause ground loops that will effect your pixel data streams. This is not very likely in most cases, but it can happen.
6. Grounding of LV supply V- to the chassis ground is not a safety issue (accept in very rare cases) if the supply output is isolated and below a certain voltage. It is a noise or ground loop issue. In many studio audio systems they even use a separate ground for the audio and video systems where everything that is a signal ground comes to a single common point and no power equipment is allow to be grounded at that point.
The bottom line here is that for "what we do in this hobby" (for the most part) the grounding of the V- is at best arbitrary when relating to noise. It is a good place to start if the system you use allows for it, but if you do it, make sure you have only one single point of common grounding for your data. If you chose to float your supplies, you will also need to be aware of possible noise issues from stray EMI (Electromagnetic Interference). Sometimes grounded systems have a higher immunity from this noise issue... Sometime the ground loop issue can be your problem with or without the grounding of the V-. Like I said, ground loop trouble shooting can be a black art at best.
Use "best practices" for starters and stay safe at all costs. As for what "best practices" means... I went to school for a long time and have 30 plus years at electrical and electronic design and installation... I can't give you that definition... it is too broad and has too many variables.. You are kind of on your own.. Good luck..
deonb wrote:....I hope nobody use this thread to make an authoritative decision one way or another. Except for one thing - PLEASE don't take the E682 manual literally and wire up V- to an open Ground connector on the power supply....
Sounded "authoritative" to me... 🙂
LightUp wrote:Sounded "authoritative" to me... 🙂
You need quote his ENTIRE sentance for context.. he is actually 100% correct which makes it an accurate authoritative comment in the proper sense.. (did I just say that?)...
